The white nylon/plastic rear handle/tank assembly of Stihl chainsaws are very hard to clean up and keep them looking good, only scraping away a layer of stained surface material will expose new white material beneath. It will stain again quite quickly if handled with dirty hands as scraping or even sanding leave the surface slightly roughened and porous. My best results have been to scrape, sand and expose the white layer beneath, then polish the entire area with a piece of similar material, I use body fill applicators, the white ones bought from autobody supply houses or paint suppliers.
I have used gasoline, WD-40 or Brakecleaner on my saws. I always used Castrol Super Clean on all of my Stihl saws verses no experience with other brands. Like Holdman ,we are in the tree business and our saws get looking ugly in no time.
Below, I’ll teach you how to clean a chainsaw so it looks spotless and runs like new again. As for cleaning the chainsaw guide bar groove, you can either use a special groove cleaning tool or a putty knife. I hope you enjoyed this post on how to clean a chainsaw.
best way to clean chainsaw plastic Related Question:
Can I clean my chainsaw with wd40?
We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.
What are Stihl plastics made of?
Stihl uses mostly glass fiber reinforced plastics to give its parts more strength. These are similar to the type of plastic used in tool bodies. Given how injection molding works, to make lots of parts, you need lots of plastic. You also need the means to both store it and move it around the facility.
Can you use brake cleaner to clean a chainsaw?
Can I Use Brake Cleaner To Clean My Chainsaw? If you are washing parts that are covered in oil, you should never use water on them. Instead, use carb or brake cleaner to blow out the dirt and oil more effectively.
Can you put seafoam in a chainsaw?
At Sea Foam, we recommend overcoming saw starting issues by adding 2–4 ounces of Sea Foam Motor Treatment to a low tank of fuel, running it for about five minutes, then letting it sit a night or two to soak or clean. Add fresh fuel and proper two-stroke oil before operating and it’ll be good to go.
How often should you clean your chainsaw?
BEFORE AND AFTER EACH USE: Keep your chainsaw running smoothly by spending an extra minute or two before and after each use to inspect your chainsaw. Clean the chainsaw bar after each use by scraping out any debris inside the track.
What can I use to clean my chainsaw?
In a well-ventilated area, take a bucket and mix one cup of ammonia with one gallon of water. Place the chainsaw chain in this solution and let it soak for 15 minutes. Put on a pair of thick rubber gloves for protection. Then, use a soft-bristled toothbrush to scrub each section of the chain until it’s free of debris.
Do I need to clean my chainsaw after use?
After each use, wipe the chainsaw housing clean with a damp cloth. For battery models, you should also use the damp cloth to clean the battery and the battery slot. A paintbrush is useful for cleaning electrical contacts.
Can I use petrol to clean chainsaw chain?
Gasoline doesn’t age well. If your chainsaw has been idle for a month then you will want to drain and refill with fresh fuel. If it has been idle for more than three months then you will want to drain the fuel and clean it. Liquid in the gas will begin to evaporate and leave behind a sticky goo.
How often should you oil a chainsaw?
The chain saw should be oiled before each cut. For Manual Oiling System: Lubricate the saw chain by pressing the bulb on the oil reservoir cap twice before making each cut. Hold the bulb down for 3-4 seconds on each press. Automatic oiling system will keep the bar and chain constantly lubricated.
Do you need to oil a chainsaw blade?
To work properly, chainsaw chains and bars must be lubricated.In the past, most operators have used petroleum-based oils. When a chain saw is used, virtually all of the lubricant ends up in the environment.
How do you clean and sharpen a chainsaw?
I clean all my saw chains before sharpening with Simple Green (environmentally friendly). I spray them and let them soak for a few minutes, then scrub them with a toothbrush on both sides–that usually gets the gullet clean as well. Then I rinse them in water and air-gun them to get moisture out of the nooks.
Can you put carb cleaner in a chainsaw?
Firstly, blend some carburetor cleaner with the gas in your chainsaw’s fuel tank. I recommend blending 4 ounces (113 grams) of the B12 carburetor cleaner with a tankful of gas. Use a funnel to add the carburetor cleaner into the gas tank slowly.
Can you clean a chainsaw carburetor without taking it apart?
To clean a carb, you have to take it apart. If it needs cleaning, the parts that need cleaning can’t be seen from the outside.
How often should you change the spark plug in a chainsaw?
A poorly functioning engine in a Stihl chainsaw can mean more work for the operator and can even be dangerous. Consequently, Stihl recommends replacing the spark plug after every 100 service hours.
How do you clean a chainsaw without a compressor?
Make a solution using a gallon of water and a cup of household ammonia and soak these parts in the solution for 20 minutes. Once the soaking time is over, take them out and scrub using a stiff brush. Rinse them thoroughly using warm water.