Check and replace bar and chain oil regularly to reduce friction, keep the saw from wearing out faster, and to make cutting easier. Be sure to use bar and chain oil, Not regular motor oil. Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
This is different than the oil that you mix with your gas to provide lubrication to the engine, and I’m going to describe below the importance of this task and explain how to oil your chainsaw for both the safety and care of your saw. Most saws come with a sample bottle of oil and suggestions of which oil to by- but for the most part, the oil is that same from one brand to the next. Saws are designed to feed oil as it runs, so most tanks are large enough to hold enough oil for a full tank of gas.
Lucky for you, we have compiled four commonly found alternatives to expensive chainsaw bar and chain oil – plus two last-ditch variations to be used only in the most desperate of times. As mentioned above, motor oil and hydraulic fluid can be mixed with the existing chainsaw bar and chain oil to extend its lifespan. Again, we’d like to remind you that filtered used motor oil is not a good long-term solution for chainsaw bar and chain oil.
how to oil chainsaw bar Related Question:
How do you add oil to a bar?
The steps are quick and easy: Set your chainsaw on a level surface, bar side down so that it lays flat. Allow a minute for the oil to settle, then unscrew the cap to the saw’s bar and chain oil reservoir. Using a small funnel, slowly pour the bar and chain oil into the reservoir, taking care not to overfill.
How often do you oil a chainsaw bar?
It is recommended that you grease the bearing in the tip of the bar each time you refuel. Make sure to grease the tip at the end of the day as well to help prevent moisture from entering the bearing as the bar cools.
Can you use regular oil for chainsaw bar?
Whether you use bar and chain oil, traditional motor oil or a vegetable oil-based lubricant, always make sure you’re using fresh oil when you fill your chain saw’s bar oil reservoir. Never use waste oil that you drained from your car or boat.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Can I use WD40 as chainsaw oil?
No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant. WD40 is primarily a solvent or rust dissolver.
What weight is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Why is my chainsaw using so much oil?
What causes a chainsaw to leak oil? As the oil is pumped from the tank through to the guide bar, air begins to replace the space where the oil was previously stored. If there isn’t proper ventilation of the oil tank, a vacuum can occur and reduce the flow of oil to the guide bar.
Can I use 5w30 for bar oil?
You’ll be fine.
Can you use 10w40 in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30. Thicker.
Can I use 2 stroke oil for chainsaw bar oil?
Can You Use 2 Cycle Oil As Bar Oil? You should only use two-cycle oil as the mix, never as a chainsaw bar oil alternative. Using two-cycle oil on the bar will not provide enough tackiness to stick to the chainsaw chain in the summer months. Two-cycle oil also will not work in the winter.
Can you use transmission fluid for chainsaw bar oil?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .
Can I use vegetable oil instead of bar and chain oil?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
How do you deep clean a chainsaw?
In a well-ventilated area, take a bucket and mix one cup of ammonia with one gallon of water. Place the chainsaw chain in this solution and let it soak for 15 minutes. Put on a pair of thick rubber gloves for protection. Then, use a soft-bristled toothbrush to scrub each section of the chain until it’s free of debris.