This is different than the oil that you mix with your gas to provide lubrication to the engine, and I’m going to describe below the importance of this task and explain how to oil your chainsaw for both the safety and care of your saw. Most saws come with a sample bottle of oil and suggestions of which oil to by- but for the most part, the oil is that same from one brand to the next. Saws are designed to feed oil as it runs, so most tanks are large enough to hold enough oil for a full tank of gas.
Check and replace bar and chain oil regularly to reduce friction, keep the saw from wearing out faster, and to make cutting easier. Be sure to use bar and chain oil, Not regular motor oil. Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
At Gardening Products Review, we highly recommend oil manufactured for this specific use. Chainsaw shown in this video tutorial is the Redback 40V 12″ Li-Ion Cordless Chainsaw. The bar & chain oil featured in this video is Husqvarna Bar & Chain Oil – 1 Gallon.
Incorrect/Inappropriate Correct/Appropriate Cutting non-wood material such as plastic, masonry, or metal Use a miter saw, oscillating multi-tool, or rotary saw for these materials instead Cutting dimensional lumber such as four-by-fours Use a circular saw or reciprocating saw instead Splitting logs Use a log splitter Cutting on the ground Elevate the material Pinch chainsaw bar in the cut Add pressure below the material to widen the groove Cut with top of the chainsaw guide bar Cut with the bottom of the saw guide bar Plunge cut with the nose of the saw Cut only on the bottom of the saw bar Limit the operation of the chainsaw to outdoor areas. Understand All Parts of the Chainsaw Learn about each part of the chainsaw and its function before powering up the saw. Prevent Kickback Chainsaw kickback happens when the upper quadrant of the nose of the chainsaw guide bar touches an object when the chain is moving.
how to oil chainsaw blade Related Question:
Do you need to oil a chainsaw blade?
To work properly, chainsaw chains and bars must be lubricated.In the past, most operators have used petroleum-based oils. When a chain saw is used, virtually all of the lubricant ends up in the environment.
What kind of oil do you use to oil a chainsaw blade?
Petroleum-based bar oil has been the standard for chainsaws. Lightweight oil is used in winter and heavier oil in summer. Manufacturers of chainsaws make bar and chain oils specially blended for their machines to extend their lifespan, but if they are not available, the owner’s manual suggests alternatives.
What happens if you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Can I use WD40 as chainsaw oil?
No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant. WD40 is primarily a solvent or rust dissolver.
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Can I use vegetable oil as chainsaw oil?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
Can I use regular oil for chainsaw bar?
Generally, chainsaws can handle a wide range of lubricants. Vegetable and canola oils work well, and automobile motor oil will too, as long as you observe the SAE ratings and use the appropriate oil weight for the season. Always use fresh, never used, oils.
Can you use 5w30 in a chainsaw?
Yes. almost any oil better than nothing.. even other oils ate used if U cut edible things or plastic. if possible mix it with a part of sticky chain oil so it dont geet centrifugated so easy.. but also in some aplications the non sticky oil is used to centrifugate dust.
How often should I oil my chainsaw?
It is recommended that you grease the bearing in the tip of the bar each time you refuel. Make sure to grease the tip at the end of the day as well to help prevent moisture from entering the bearing as the bar cools.
How much oil should a chainsaw use?
When to Oil Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
Why does my chainsaw blade go dull so fast?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
What can I do with an old chainsaw?
Gas and oil can be disposed of at a household hazardous waste collection site for free. Remove non-metal parts and place in the trash. Metal parts can be recycled as scrap metal.
What weight is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
Can you use transmission fluid for chainsaw bar oil?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .