First cut should cut should be made from the underside towards the top about 1/3 of the way through the log. Once you had assessed the situation, begin to cut the limbs supporting the tree, cut from under these limbs to avoid the chainsaw getting pinched or stuck. Make an initial cut upwards, about 1/3 of the way through the branch, a short distance from the trunk of the tree so you have room for the final cut which will be close to the trunk.
The V shaped cradle works well for ‘noodling’ as well, which it sounds like you’re doing. I’m sure it’s been done time and time again, but I was looking at the rack we used to stack tobacco sticks in to bundle up, and realized it was ideal for holding logs steady to do just that.
A log holder attaches to the top of your electric chainsaw and holds logs in place so they don’t move while you’re cutting them. If you’re just beginning to cut tree logs with a chainsaw or chainsaw mill, then it might take some practice in order to develop the right techniques for holding onto logs securely. It is important to learn how to hold logs while cutting with a chainsaw for safety reasons.
Cutting logs with a chainsaw can seem daunting, especially because it’s one of the first skills learned by chainsaw users. In this guide, we’ll be covering the following 8 steps, which will show you the basics for how to cut logs with a chainsaw. Basically what can happen, is if you hit that part of the chainsaw against a piece of wood, it catches the chain and throws the whole chainsaw back towards the user.
how to safely chainsaw small logs Related Question:
How do you saw a log on the ground?
Cutting a Log on the Ground Technique Start cutting from the top of the log, applying light pressure to the chainsaw. The chainsaw should do the work, and the teeth should pull the chain bar into the wood. Don’t let the guide bar nose or chain touch the ground or other objects.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
Can you cut wet logs with a chainsaw?
Can you cut wet wood with a chainsaw? Yes, you can cut the wet wood with a chainsaw. Besides, there is a misconception that wet wood can impact the chainsaw bar and chain. But actually, the damp wood will not dull the chainsaw any faster than using it on other types of wood.
How do I stop my chainsaw from pinching?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
Can you cut sideways with a chainsaw?
While a properly working chain saw helps you cut hours off your work time when felling trees or cutting logs for firewood, it can also be a dangerous tool when things go wrong. When a chain saw cuts sideways, it’s a clear indication that things aren’t as they should be.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
What’s the safest chainsaw?
Chainsaws are useful when doing work on your home, but they can feel dangerous to use. It’s not too bad if you know what you’re doing, but it’s so easy to make one wrong move—and then it’s game over. Enter the WORX JawSaw.
How often should you flip the bar on a chainsaw?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
Why does my chainsaw get dull so fast?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
How often should you change your chainsaw chain?
The chain sprocket must be replaced if the depth of the wear marks reaches about 0.5mm, i.e. the wear limit. A seriously worn chain sprocket can cause the chainsaw chain and guide bar to wear at an increased rate, as well as reducing cutting performance too, so it’s important to keep an eye on.
Can you cut logs with a miter saw?
To cut your wood slices, we strongly recommend you have either a miter saw or band saw. These are the best saw options to use when cutting log slices, as they can make more precise cuts with the uneven nature of a log. They can also cut thicker pieces of wood than other types of saws.
How are logs turned into boards?
Similar to cant sawing, plain sawing begins with rotating and sawing the outer sides of a log into boards until the center is squared into a four-sided cant. Instead of leaving the cant as is, it is rotated and sawn to produce the maximum amount of lumber.
How do you cut small wooden discs?
Cutting a circle in wood with a hole saw. Using a hole saw is the absolute easiest way to cut circles in wood for your project. All you have to do is lock your hole saw in the chuck of your drill or drill press and start cutting. You can use hole saws to cut circles from ¾ inches up to 7 inches in diameter.
What is the smallest diameter log worth milling?
I always tell my customers that anything smaller than 8″ on the small end is usually not worth the trouble. Some customers take it to heart and some will throw in everything down to 4″. I will saw a 6″ log if it’s straight but the 4 and 5 inch stuff usually gets put aside.
What should you not do with a chainsaw?
Don’t Cut With Improper Blade Tension A overly loose or tight chain also wears out the drive sprocket and causes rapid chain and bar wear. To determine if your chain is properly tensioned, pull up on the chain. The drive links should still be in the bar groove. If the links come out of the bar, the chain is too loose.