Proper chainsaw chain tension is almost as important as the sharpness of your chain. It just takes a little practice but once you find the right amount of tension, adjusting the chainsaw chain tension is really easy. Proper chainsaw chain tension is safer, it cuts better and it will extend the life of both your chainsaw and your chain.
Tightening the screw will tighten the chain, and loosening will loosen the chain. Visit our Chainsaw Chains page to our inventory of available replacement chains and other chainsaw accessories. eReplacementParts.com stocks thousands of parts for many major chainsaw brands, including Echo chainsaw parts.
Important: Always make sure the engine is turned off before you begin tensioning the chainsaw chain. Locate the chain tension adjustment points on your chainsaw. Common locations for adjustment points include the side cover and the front of the chainsaw.
how to set chainsaw tension Related Question:
How much tension should be on a chainsaw chain?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
What is the correct chain tension?
A properly adjusted chain should hold itself up against the bottom of the bar. You don’t want the chain to sag, but you don’t want it so tight that it damages your saw as it spins around the bar. To start with, look at your chain. If you can see the chain sagging down from the bottom of the bar..it’s too loose.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
Why is my chainsaw blade smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Why does chainsaw chain keep coming loose?
Chain Not Set Properly One of the most common reasons why your chain might be coming loose is because it was not set properly. When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won’t change as you work your saw.
How long should a chain on a chainsaw last?
The lifetime of a chainsaw chain has no fixed limit and depends on usage and maintenance. The chain should last many years; 5-6 years should be no problem. However, if the chainsaw chain is used properly and taken care of, it can last way longer.
Why does my chainsaw blade go dull so fast?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
Why does my chainsaw cut on a angle?
Check the size of the top plates, which sit on the longer sections of each tooth on the chain. These top plates should be the same size. If some are shorter than others, file the longer ones down to match. Keep the same angle on all the top plates as you file – angles that don’t match also can cause curved cutting.
How many times can you sharpen a chainsaw?
Cutters can be sharpened up to 10 times or more before the chain needs replacing. If your cutters are worn unevenly after a few sharpenings, a professional can regrind them to uniform shape. If you use the same chain for a few years, then buy a new one, the new one won’t mesh smoothly with the sprocket and bar.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
Why does dirt dull a chainsaw?
Don’t Cut Into Dirt All it takes is a second in the dirt to dull the cutters. In addition to dulling the cutters, dirt also wears out the chain links faster, causing the chain to stretch. Plus, dirt wears the sprocket at the bar tip.
Why do loggers run upside down bars?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
Will cutting wet wood dull a chainsaw?
Does Cutting Wet Wood Dull a Chainsaw? Using your chainsaw to cut through wet wood will not dull the chain any faster than using it for other types of wood. When you think about it, your chainsaw chain is already wet. True, it is not wet with water.
Does hard wood dull a chainsaw?
Re: Chainsaw and oak Very hard but really puts out the heat in the fireplace. If you cut it green it is not too bad. After it has dried it will dull a chain about each tank of gas. And that was Stihl chain.