The thin kerf and wide set teeth enable a blade like this to cut to softwoods like pine and pressure treated beams a little more easily. The excessively high tooth count cut very slowly, which actually can cause the blade to become pinched between the pieces being cut and cause burning. Not related to the cut itself, but the blade doesn’t have any relief cuts or stabilizer vents.
To save you time and money from damaged materials, I have written the best circular saw blade for plywood reviews. While cutting plywood with a circular saw, stack a sheet face down so that chips or burrs appear on the bad side, where your saw slides. Back to menu Circular Saw Blade for Plywood FAQ. In this section, I answered frequently asked questions from my readers about working with plywood.
While the saw is ideal for those purposes, you can also use it to make furniture-grade cuts in wood, cut steel or aluminum, reduce unwieldly sheets of plywood to more manageable sizes, and do heavy demolition cuts through lumber that has nails in it. These blades are rated for steel plate, pipe and conduit, and shapes such as L, U, and squares; some blades are also designed for cutting the same shapes in aluminum, and a few blades are even rated for making the cut in stainless steel, a notoriously difficult material to cut. Not all metal-cutting circular saw blades will cut thin sheet materials such a roofing and metal trim.
165mm circular saw blade for plywood Related Question:
What blade is best for cutting plywood?
To get the best-quality cuts, invest in an 80-tooth blade designed for sheet goods. The small teeth take little bites to reduce chip-out and are steeply beveled at their edges to score the veneer face. You’ll have to slow your feed rate, but will get a much smoother edge.
How many teeth should a circular saw plywood blade have?
Framing blades have 24 teeth and are effective for jobs such as rough carpentry, where speed is more important than getting a clean cut. Plywood blades have 100 or more fine teeth designed to create a finish with minimal splintering.
What circular saw blade is best for cutting plywood and why?
Best Circular Saw Blade: Ultra Fine Finish With 60 teeth and a . 059-inch kerf, the Freud D0760X Diablo Circular Saw Blade creates clean, smooth cuts on delicate material like veneer plywood and melamine. This thin kerf greatly reduces the chance of chipping and blowouts, and doesn’t waste any material.
Can you cut plywood with a circular saw?
Circular saws can be used to make square, miter, bevel and compound-angle cuts. When fitted with the appropriate blade, it can even cut metal and concrete. However, there’s one job for which the circular saw is particularly well-suited: cutting large sheets of plywood down to size.
How do you cut thin plywood without splintering?
Naturally, you’ll want to select a fine tooth blade that works well to cut plywood. These tend to have more teeth per inch, as well a higher bevel angle that can slice through the wood. For a circular saw, you can easily pick up a plywood blade for $20 at any home center, and it will work magic on your cuts.
What do you put under plywood when cutting?
The Secret is 2×2 Foam Board Here I have 8 laid out to support a full sheet of 3/4″ plywood. And unlike full insulation sheets, they are so easy to store. I just stack them up on a top shelf or under my bench.
How do you cut thin plywood?
To cut thin plywood correctly, you need to use a table saw with a blade that has a high teeth count. The more the teeth on the saw blade, the better it will cut plywood. You can also tape down both sides of the thin plywood with masking tape as that will prevent it from tearing or breaking.
What is a 24 tooth blade used for?
For most construction work, a 24-tooth general use blade is sufficient. That blade is very aggressive and will help you rip and cross-cut lumber and sheet goods quickly and with a high degree of accuracy. With a 24-tooth demo blade, you’re getting work done quickly, but you won’t get a near-finished edge.
What is a 180 tooth saw blade used for?
Designed for cutting a variety of materials, including plywood, vinyl siding, and plastic, the CRAFTSMAN 10-in 180-tooth high-speed steel miter/table saw blade set is a must-have for your workshop.
Is more teeth on a saw blade better?
Blades with more teeth yield a smoother cut. Blades with fewer teeth remove material faster, but tend to produce a rougher cut with more “tearout”. More teeth means you will need to use a slower feed rate.
How do you cut Luan plywood?
You CAN cut luan along the grain (cutting along the 8 foot length) without scoring, but is is always best to score it before cutting no matter which direction you cut. There is one way to greatly help limit the splintering when cutting any wood veneer: Place masking tape over the cut line first.
How many teeth do you need to cut OSB?
This amount of chip-out is virtually impossible to mask, and it makes for unattractive, amateurish edges on furniture and cabinets. A better solution is to use a blade designed for what you’re cutting. A plywood blade should have at least 80 teeth, and some have as many as 120.
How many teeth do you need for plywood?
Cross-cutting wood or sawing plywood: Use a 40-tooth to 80-tooth blade.
How do you cut 2mm plywood?
2mm birch ply would be hell with a skinny Xacto knife but it does cut decently with a sturdy utility knife. Another option that works well is a hand fret saw used with a “birdsmouth” bench board.
Can you cut thin plywood with a Stanley knife?
Stanley Knife. That’s all I ever use on thin ply – just ensure the blade is sharp (if isn’t, then change it), keep your hands behind the blade (been there, done that) and use a guide for the blade, preferably metal. Also, use several light strokes – Don’t force the blade – you’ll get through the wood eventually.
