These are the tools we recommend as “Must Have’s” for getting started and setting up shop. These silicon plugs can handle oven curing making them perfect for Cerakote and DuraCoat use. The kit comes with many size plugs allowing you ability to plug other small holes as well whose tolerances could be affected by unwanted coating getting in.
I will be painting a few metal parts around 21 square foot and only once a week. Also was looking into turbine spray gun systems but don’t know if those can work for Cerakote.
best air compressor for cerakote Related Question:
What size air compressor do I need for Cerakote?
Cerakotes requirement is 100-120 grit at 90-100 psi IIRC. You need a 10 CFM compressor on a 60 gal tank at a minimum to get the job done properly.
What airbrush is best for Cerakote?
Iwata Eclipse HP CS It is capable of patterns from hairline to 2″. This airbrush can achieve fine details even with thicker products such as DuraCoat and Cerakote. If you are painting detailed projects, the Iwata Eclipse HP CS is the airbrush to get.
How much PSI is needed for Cerakote?
20 to 25 psi is the recommended air pressure for spraying Cerakote. Practice: Start spraying on a piece of white paper to adjust the spray pattern and practice your spraying technique. Spray with the gun 3 to 5 inches away from the paper and adjust the spray pattern to between 2 and 3 inches wide.
Can you air dry Cerakote?
9) Allow to air-dry. Parts will be tack free after approximately 35 minutes. Until this point the coating is still wet, so take care to not bump or touch the parts. Parts will be partially cured after 24 hours and fully cured 5 days after application.
What’s better DuraCoat or Cerakote?
Cured Cerakote absolutely beats cured DuraCoat in every measurable respect with regard to finish quality, abrasion resistance, and overall toughness.
Does Cerakote have to be baked?
Recommended Cure Temperatures Cerakote can be cured at the maximum Recommended Cure Temperature listed in the All in one TDS, based on color and substrate. Standardized curing temperature for H-Series is done at 250°F for 2 hours following a 15 minute ambient flash time.
What temperature is Cerakote?
For optimal cure, place the coated pieces in a 250°F oven and cure for 2 hours. For a quick cure, 1 hour at 300°F is sufficient. If the substrate material is heat-sensitive (such as plastic or wood) then a 200°F cure for 2 hours is adequate.
Which Cerakote is air cure?
Cerakote Piston Coat C-186 is a dark brass/gold with a soft metallic finish. Piston Coat is an ambient (air) cure, thin film ceramic thermal barrier designed to be applied on internal engine parts that require a thermal barrier.
What is better than Cerakote?
GunKote is the biggest competition for Cerakote; each have their own following for being “the best” firearm coating, and both are comparable when tested against corrosion, chemicals, and durability. KG Gunkote also has two series, the 2400 Series (Oven Cure), and the 1200 Air Cure Series.
Does acetone remove Cerakote?
Acetone will not harm a fully cured Cerakote finish.
Is air cure Cerakote durable?
Ceramic Firearm Coatings are designed to provide a high- quality, long lasting finish for firearms and firearm accessories. Cerakote® H-Series coatings are durable, corrosion-resistant and provide unparalleled levels of hardness and adhesion.
Can you Cerakote without sandblasting?
Using the right sand blasting media is essential to achieve the correct mechanical profile for Cerakote to bond properly. Good mechanical adhesion is key to Cerakote’s performance attributes.
What is the most durable gun coating?
Cerakote Pros: Probably the most rugged finish available for your firearm. Impervious to solvents, cleaners. Can be applied over metals, polymers, wood.
Does Cerakote scratch easily?
Hardness: Test reports have rated cerakote coatings with a pencil hardness of 9H. Other than hardness, there is a scratch resistance rating of 6H. Cerakote ensures that you don’t end up spoiling your firearm because of any scratches or nails.
How long is Cerakote good for?
Details for Cerakote Storage We warranty all Cerakote products for 12 months from the date of shipment.
