09-21-2006, 1:38 PM #6 I have been thinking along the same line and have found a suitable old air tank. I would think that an inline aux tank would have the same problem but even more so as when you run out of stored air your compressor has to work double time to fill both tanks and is probably not designed to work that hard. Jay, if i where you i`d just pipe your garage normally as you would for any compressor, continue to use your little unit and if you find the need for more stored air then add a spare tank by hooking one up with regular air hose off one of the drops that way you can remove it when you don`t need it.
When you need air at the job, plug a second air line into the discharge coupler on the secondary tank, and air from both compressor tank and secondary tank will flow down the line to your air tool. To use an air nailer for shingles on a roof for example, it would be so much more convenient to leave the heavy air compressor at ground level, run an air line from it up to the secondary portable tank on the roof, and then run an air line from the secondary tank to the nail gun. If you add another air tank to your air compressor, you will be able to use higher demand air tools for a longer period of time.
Moving the compressor to a convenient spot means adding about 30 feet of pipe from the compressor to the shop. If I use 1½-inch PVC pipe from the compressor to the shop and then neck it down to ¾-inch inside the shop, this should increase the capacity of the compressor, but I’m not sure how much. Anytime you can increase the capacity of the system, it will take the air compressor longer to build pressure the first time, but after that, the compressor won’t run as often to maintain the pressure.
how to expand air compressor capacity Related Question:
How do you manage multiple compressors?
In general, the simplest way to control a system of three or fewer compressors is with manually set load/unload pressure bands arranged in a cascade arrangement, typically with all the pressure bands the same width, but each band offset slightly by about 5 psi.
How do you calculate air tank capacity?
A straightforward rule for sizing an air receiver tank for a reciprocating air compressor is to take the tool with the highest CFM requirement at the required PSI, multiply that CFM requirement by 1.25 or 1.5, then round up to the closest gallon size.
Does tank size matter air compressor?
Tank size matters—sometimes The compressors we chose have tanks ranging from 1 to 6 gallons. A larger tank holds more air and will allow you to use more air before the pressure drops and the motor kicks on to refill the tank. That might let you avoid stopping work while the compressor refills the tank.
Is it a good idea to connect two tanks to one air compressor?
Air Compressor Run Time- Connecting two or more air tanks together will in fact get you more air on reserve to use before your compressor runs, but it will also take your compressor longer to get the pressure built up in two tanks rather than one.
What is multiple compressor system?
A multiple-compressor refrigeration system for use in commercial refrigeration applications includes a plurality of compressors of unequal refrigeration capacity connected in a refrigeration circuit that includes a condenser and a plurality of associated evaporators and expansion devices in remotely located
How is air compressor capacity calculated?
Theoretical capacity of compressor is defined by geometric measurement of air in the working area during one suction period. Then this volume is multiplied by the number of periods (cycles) per time unit.
Why are air compressors bigger?
Air compressors need to be sized large enough to adequately supply peak demands; if they aren’t, the system pressure will fall during a time when you need it the most. But, typically, peak flows occur only a small fraction of the time, and the remainder of the operating hours are spent at lower flows.
Is 150 PSI air compressor good?
The best air compressors for home use should have enough power to run all your tools while remaining compact and easy to transport and store. For home use, you will need at least 150 PSI to run a wide variety of tools.
Is a 6-gallon air compressor good for air tools?
Tools that require only quick bursts of air, like pneumatic brad nail guns and finish nail guns, drain the air tank much more slowly. For these tasks, 2- to 6-gallon tanks are sufficient.
What is CFM air compressor?
CFM stands for cubic feet per minute. This is the air flow or air volume that a compressor can supply – or its output. Many pneumatic power tools require a CFM of about 5, but it really varies. A pneumatic stapler might just need 0.3 CFM, while a framing nailer may require 2.2 CFM.
