After nearly 40 years of using angle grinders my friend has told me that I’m putting cutting discs on the wrong way up. Never had a problem in all that time and do it the way I was shown by my foreman when I was 16. Could be him that’s wrong, but knowing my luck it’s probably me.
Remove the Angle Grinder DiscRemoving the Angle Grinder disc with factory keysYour new grinder comes with two separate keys that look like flat wrenches. Removing the Angle Grinder disc without keysUsing the palm of your hand, slide the disc in the direction opposite to the arrow on the disc. The main thing is that when changing a disc on a grinder, do not violate safety precautions and remove the disc with the angle grinder turned off.
The cutting disc used in the angle grinder has the front and back requirements when installing. Let us see the installation steps of cutting disc for an makute angle grinder. Then install the cutting blade, install the external fixing nut of the angle grinder on the cutting blade and fix it tightly.
For the best results, ensure that the angle grinder stays tilted at a 90 degrees angle to the surface you’re cutting. You can also try to use a sliding/rocking motion still in the angle grinder cutting direction – move the cutting wheel into then through your workpiece instead of straight down. In addition to maintaining the correct angle grinder cutting direction all through, there are several good practices you should follow to maximize the performance of your grinder.
angle grinder nut which way up Related Question:
Which way should an angle grinder spin?
Every right-angle grinder is marked with a directional arrow on the head of the grinder that indicates the direction the wheel is rotating when in use. For optimal performance, it’s important to orient the cutting wheel so it rotates into and pulls itself into the workpiece rather than rotating away from the workpiece.
Can you use a cut-off wheel on an angle grinder?
Usages. You can use cut-off discs for cutting metal bars, metal tubes and small pieces of metal sheets and plates. You can also cut out welds with them. For shortening the length of various bolts, it is also a good idea to use an angle grinder and a cut-off wheel.
Can I use bigger disc on angle grinder?
Fitting a 14 inch (356 mm) cut-off disc to a 9 inch (230 mm) angle grinder will increase the edge speed excessively to at least 120 m/s (430 kmph). The photograph below shows an angle grinder with the wrong size cutting disc fitted and the guard removed.
What is the arbor on a grinding wheel?
Attach cutoff wheels, grinding wheels, and other abrasive wheels to hand-held drills and die grinders. Arbors are also known as mandrels. For technical drawings and 3-D models, click on a part number.
What is the arbor on an angle grinder?
Adapting the spindle from a small “foreign” size to the American size, so we can have a wider choice of abrasives. “The “standard” spindle (sometimes called the “arbor”) thread these days on a angle grinder in the US is 5/8-11 (5/8″ diameter and 11 threads per inch).
Why is it important to point an angle grinder downwards when starting it up?
If a climbing cut (cutting from the front of the workpiece with sparks being thrown downwards) is essential because material must be cut in place and can’t be held in a vise, make sure sure you keep your head out of the way. Otherwise, you can be hit in the face if the grinder kicks back upwards.
What direction should you feed the cutting disc into the workpiece?
The direction of the cutting motion is important. Always feed the cutting disc into the work so that it cuts in an upward direction.
What is the difference between a cutting disc and a grinding disc?
Clue is in the title, a cutting disc is thin and used for cutting and a grinding disc is much thicker and used for grinding not cutting.
What grinder collects the most kief?
Any grinder with a kief catcher will work, but the Santa Cruz Shredder or ZAM grinder are two of the best weed grinders for collecting kief.
Do you push or pull a grinder?
You should work with a straight grinder when cutting using the side (of the bit) and a 90-degree grinder when you are using the front (if possible). That way, you’ll have more control of the thrust and you won’t worry about the tool grabbing or pulling at you.
Are 9 inch grinders banned?
Caution: 9 inch (230 mm) angle grinders have been banned on some work sites due to the increased risk of injury. The increased power and size of the unit will cause more severe kickback and gyroscopic effects (i.e. makes the grinder difficult to manoeuvre).
