My intent was to us the saw to cut out blades and then put saw and table away when not in use. Good decision, I use that little saw for so many things. Cutting pins, trimming handle materials, cutting bolster material, opening steel packages from Aldo and the list goes on and on.
An angle grinder is a hand-held power tool used for cutting. Many different types of cutting wheel can be mounted on an angle grinder but they’re all essentially grinding wheels. Our vertical bandsaw is used more for cutting shapes than cutting to length.
I have almost everything, 4 by 6 bandsaw, portaband, portaband on a stand,angle grinder with a thin cutting wheel usually fitted, another angle grinder with a regular abrasive wheel usually fitted, a dremel usually fitted with a cutting disc, an abrasive disc chop saw use of a circular saw if Ineed to cut Aluminium sheet, and a bench mounted shear for thinner stuff. This 100yr old machine will virtually silently cut its way through anything within its capacity and turn itself off once the job is done. It is fairly, though not perfectly accurate ( Within 15 thous in 4 inches depth of cut.
I have until now just used an angle grinder to roughly cut out my knife blanks from ground flat bar and then grind to the line on the bench belt grinder and that is working out ok. I have been wanting to pull the trigger as it were on one of these portable metal cutting bandsaws for a few months but trying to justify the cost for doing the same job as my angle grinder. Metal cuttin bandsaws are more than worth their cost, you won’t be throwing away as much materials as with an angle grinder.
If you buy a metal bladed chop box you can just buy wood blades and be able to cut wood, just not in the metal area so there is no flammable saw dust from wood….its more versatile than an abrasive cut off saw for hobby. Even if you go with the abrasive cut off saw its 100% better than the 4 inch angle grinder for both speed and accuracy. Never having tried another chop saw I am going to venture out on a limb and say it’s pretty awful as chop saws go, but I don’t regret this particular purchase, it fills a need for a reasonable price point.
If you are making things that can be completely cut before assembly, the bandsaw is good. Then while it’s cutting, mark the next set of pieces to be cut. The bandsaw seems to leave less cleanup of the cut before assembly also, except for what is mentioned below.
I have already purchased pretty much everything I need to start fabricating but I am completely stuck at which saw to purchase. “So in all my research it seems like most people prefer a carbide steel blade for a saw, but the downsides seem to be that if you have to cut rebar or something fairly hard, you run the risk of breaking teeth off a $100+ blade, or at least dulling it very quickly. Then my most recent research brought me to benchtop band saws… yes they are a little pricey but I want to get something that can cut through almost any metal and not have to worry about it breaking a blade.
Short chopping cuts will cut faster, cooler and more accurate than a steady down pressure on the abrasive blade. My chop saw is just setting collect dust, but I will drag it out to make fast cuts in angle iron. I use the band saw on round stock and thick flatbar, and large angle iron, and the torch or plasma cutter for flat plate or anything to heavy or big to fit on the other tools.
band saw vs angle grinder Related Question:
Can an angle grinder cut anything?
What is an angle grinder. An angle grinder is a power tool that can be used for different projects. You can cut metal, aluminium, concrete, bricks, pavers, wood, and other dense materials; you can sand and polish different surfaces to sharpen tools and grind materials.
What is the difference between a grinder and a saw?
On a circular saw, the blade is perpendicular to the motor. On an angle grinder, the blade is parallel to the motor so that it is used sideways for grinding and sanding. This makes a big difference in what you can do with each tool and makes the look of the tool unique as well.
Can an angle grinder be used for cutting wood?
The blade of an angle grinder is a grindstone that is used to polish or sharpen metal and stone; it cannot be used for cut- ting wood because it may burn and singe the wood by friction.
Can I use bigger disc on angle grinder?
Fitting a 14 inch (356 mm) cut-off disc to a 9 inch (230 mm) angle grinder will increase the edge speed excessively to at least 120 m/s (430 kmph). The photograph below shows an angle grinder with the wrong size cutting disc fitted and the guard removed.
Can a diamond disc cut wood?
The harsh grit of the diamond blade can cut tile and masonry with straight lines. When applied to wood, however, the blades might create a rough cut, ripping apart fibers, or might make it too easy to create crooked cuts. In most cases, it is better to use a traditional steel blade for wood.
Can you use a grinding wheel on wood?
Using your angle grinder on wood can be just as, if not more dangerous than metal. Some of the new angle grinder attachments are specifically designed for cutting wood and have many sharpened steel teeth, just like a chainsaw.
Can I cut wood with a metal blade?
You can use a metal blade to cut wood. A circular saw blade cut metal in a sluggish rotational speed of 25m/s. They are driven by a motor having high power and an A/C vector drive. They are long lasting and non-reusable.
Can I cut pavers with angle grinder?
Tips for Cutting Pavers All standard cutting methods work for straight cuts, but for curved cuts, use a circular saw or angle grinder. Score the curved cut along the top of the paver first, cutting about 1/8 inch deep.
Can a cut off saw be used for wood?
Chop saws can be used for cutting lumber, moulding, decking, aluminum and other non-ferrous metals, provided the width and depth cooperate with the size restrictions of the saw.
Can you cut cast iron with an angle grinder?
The one tool you can use and likely have on-hand is an angle grinder. While you could use a reciprocating saw or even a hacksaw to vigorously slice your way through cast iron, utilizing an angle grinder to swiftly cut segments of cast iron pipe, is a viable option too.
Can you cut hardened steel with an angle grinder?
Hardened steel is a very useful material, but working with it is tough because it is nearly impossible to cut with simple tools. What you really need is an angle grinder, and this video will show you how to use one of the powerful power tools to cut a hardened steel ring.
Can a band saw cut rebar?
The Milwaukee M12 Band Saw is the first official one handed cordless band saw so it is super easy to use holding the rebar in one hand and cutting with the other.
Can I use a jigsaw instead of a circular saw?
Although a jigsaw can be used for most of the tasks that a circular saw can perform, including straight cuts and cuts on a tilt, the jigsaw uses that really take advantage of the tool’s qualities are jobs such as kitchen fitting and joinery, with their frequent need for complex cuts.
Whats the difference between a circular saw and an angle grinder?
They are similar to circular saws because they can produce a variety of cuts and unique designs. However, they are different in their overall size, operation, and shape. Most of the time, a good angle grinder is much smaller than a circular saw and has its cutting and grinding apparatus at the end of the machine.
What can an angle grinder not cut?
The inspiration behind this creation is the natural defense mechanisms used by shells, grapefruit skins, and fish scales that makes them resistant from the attacks of various sea creatures. The material, named Proteus, cannot be cut using either angle grinders, drills, or high-pressure water jets.
