I guess it depends on what you’re using it for, and where you’re using it. The chopsaw is definitely more portable, and possibly will cut faster, but i like my bandsaw-it’s quiet, makes a very clean cut, and i can set it and let it cut while i’m doing something else and it shuts itself off when done cutting. I’ll likely pick up a chopsaw someday when i find a good deal on one at an auction, but i don’t need one bad enough to buy new.
Since your comparison just includes the band saw vs the chop saw, I would go with the band saw just because that chop saw makes me wanna scream…especially on Monday morning But seriously, I really have done my time on both machines, and a properly maintained band saw will do the better job in my opinion. If you really want a cut that is heaven sent though, use a cold saw. I know they hurt the wallet, but they sooth the soul my brotha Good luck, Rev.
There’s 3 common tool choices for cutting metal tubing: Abrasive chop-saw, Horizontal band-saw, Cold saw. An abrasive chop saw is the most cost effective way for cutting metal tubing and Also by far the most obnoxious and inconsiderate to fellow co-workers. These saws are extremely loud and generate a great deal of metal dust.
The ability to make both straight and angled cuts is what differentiates a chop saw from a miter saw, and makes a miter saw capable of angles and bevels that a band saw cannot cut. A compound miter saw usually only tilts in a single direction, to the left or right, so a compound miter saw may tilt from 0° to 90°, or from 90° to 180°, but not both. A sliding compound miter saw combines some of the features of a radial arm saw with a miter saw, and allows for mitered chopping cuts as well as shorter rip cuts.
bandsaw vs chop saw Related Question:
What is a major benefit the bandsaw has over the chop saw?
Since the blade is so narrow and it cuts downward, it has the advantage of essentially keeping the workpiece solidly on the table as you make the cut. This makes the bandsaw inherently safer than a table saw for most cuts. Making a rip cut on the band saw is a breeze, with the right blade.
Is a band saw good for cutting wood?
With the correct blade, a band saw can cut wood or metal, in either curves or straight lines. Blades come in a variety of widths and tooth counts. Narrower blades are good for tighter curves, while wider blades are better at straight cuts.
What is a band saw good for?
A band saw can be used to cut curves, even in thick lumber, such as in creating cabriole legs, to rip lumber and to crosscut short pieces. The most common use for the band saw, however, is in cutting irregular shapes. The second most common use is in resawing or ripping lumber into thinner slabs.
Is a bandsaw good for cutting metal?
Band saws are not suitable for cutting very thin sheet metal; a rule of thumb suggests the metal to be cut should be thicker than the depth of 3 band saw blade teeth, however they are excellent for cutting thin walled profiles such as box and angle.
What are the disadvantages of a band saw?
The Disadvantages: A bandsaw is limited to the size pieces you can cut because of the circular blade. With the Speedster Bandsaw and Diamond Laser 3000, the maximum size glass piece is approximately 10 to 12 inches in diameter. 2. It does not take the place of simple cuts.
What are 5 general guidelines for using the band saw?
Never push on back of piece with fingers or thumb. Don’t reach across the blade. Make all cuts under power, not while blade is coasting. Never remove guard unless authorized by Technician or WRL Manager.
What materials can a bandsaw cut?
Most bandsaws have two wheels rotating in the same plane, one of which is powered. The blade itself can come in a variety of sizes and tooth pitch (teeth per inch, or TPI) which enables the machine to be highly versatile and able to cut a wide variety of materials including wood, metal and plastic.
How high can a bandsaw cut?
The resaw capacity is the maximum height (thickness) that can be cut. For the small shop furniture maker, go with 14″ as the minimum for a bandsaw, though 16″ is better. Those doing larger work might even want 18″ or 20″ machines. Just make sure you have a minimum resaw height of 12″ for versatility.
Can I use metal saw to cut wood?
You can use a metal blade to cut wood. A circular saw blade cut metal in a sluggish rotational speed of 25m/s. They are driven by a motor having high power and an A/C vector drive. They are long lasting and non-reusable.
Is a bandsaw necessary?
No, you don’t. As a hand tool woodworker you are fully self sufficient without a bandsaw.
Why is a band saw called a band saw?
The band saw gets its name because the blade that cuts the stock is a narrow steel strip where the ends have been welded together to form a continuous band.
What is better a band saw or a scroll saw?
If you want to make fine detail cuts, inside cuts, make patterns and letters, and you want to do so on smaller pieces of wood, the scroll saw is what you want to go with. However, for large, straight, and aggressive cuts on larger pieces of wood, and even metals, the band saw is the way to go.
Can a bandsaw cut hardened steel?
Carbide band saw blades provide high wear resistance and toughness when cutting a variety of applications such as: case hardened steels, spring steels, high speed steels, nickel based alloys, case hardened steels, composite graphite, high nickel alloys, titanium, inconnel, and other exotic metals.
Can you cut Aluminium with a band saw?
With the advancements in band saw technology, large aluminum billet now can be cut almost as quickly as with large circular saws. The best news for a fabricator is that a band saw for this type of aluminum cutting application requires a significantly smaller capital investment than a circular saw.
What’s the difference between a band saw and a jigsaw?
What is this? Bandsaws are used almost exclusively for re-sawing projects. Jigsaws are, by definition, hand power tools that cut with a reciprocating motion and are generally used to make various curved cuts on thinner material.