I am planning, as a school project, to cut some antlers for the students at school to make pendants, bolos, and belt buckles. I have to cut them myself at home to take to school as I am finding antlers are somewhat expensive. Input as to glue or epoxy to make antler stick to metal, finishing of the antler after engraving or just any other thing you can think of that a beginner might need.
I need to cut the main stalk of the antlers, but the saws I’ve tried so far have given unsatisfactory results. I tried a coping saw, not surprisingly it did not leave a smooth cut. I tried my power miter saw, it cut but created a billowing cloud of noxious burnt antler smell.
I’ll have to get a cross cut or plywood blade instead of my rip blade. This has been posted on here before but a good way to cut bone on a table saw is to lower the blade and then put a thin – 1/8 pc of masonite or something similiar over the blade. “A wider blade is nice, but within reason blade tension is perhaps more important than blade width. I just use whatever nearly-worn out blade is on the saw, usually a 1/4″x6ppi.
1 I’ve got a bit of deer antler I can experiment with and can probably get access to more. 7 I have used antler almost exclusively for some years for replacements and on my instruments and found out the best pieces are antlers that didn’t grow to their full size. 8 just a quick tip for antler and bone- you can glue the piece of bone or antler to a small stick of wood when cutting on a bandsaw.
I’ve got a set of deer antlers that I’d like to cut for bone blanks and bridge insets. Well I’ve made many, many projectal pts, knives, handles, and instrument bridge inserts and etc all of the above in my bow and arrow, muzzel loading days out of bone and antler materials……………………………………. And today if I need a nut or bridge insert… I ORDER THEM…. littlepicker – Posted – 02/12/2011: 16:16:19. Lot of guys on there work with antler and bone, might give you some ideas.
best bandsaw blade for cutting antler Related Question:
Can you cut antlers with a bandsaw?
You can cut it with a bandsaw if you are VERY careful. A mandolin nut doesn’t leave much room for fingers to hold it and stay out of the saw. The bandsaw is probably the easiest thing to cut it with though. A scroll saw would work too, or a hacksaw.
What is the best saw to cut deer antlers?
A bone saw or a regular hand saw for cutting wood. Both work fine…
Can you drill into deer antlers?
To make an antler lamp, you will need to drill several holes in order to connect the antlers together. The drilling is easy, but make sure you do it correctly for a good, clean hole.
How do you cut a moose antler?
Set the saw blade horizontally just over the moose’s eye sockets and cut toward the back of the skull. Use a hacksaw if you are in the forest, or a reciprocating saw if you easily can transport the moose head to a location with an electrical outlet. Cut to a point about 3 inches beyond the rear of the antler bases.
Can you cut antlers off a roadkill deer?
“People kind of have an obsession with deer antlers, so therefore they’re cutting heads off or cutting the antlers off,” state wildlife officer Jason Keller said. “All of that is illegal, unless they do have a piece of paper that says that they legally acquired them.
Does it hurt deer to cut antlers?
When the rut is ending the buck’s testosterone goes way down, which makes the antler tissue break up. It takes a few weeks for the tissue to break up, and then the antlers shed. “Does it hurt the deer?” asked Lauren Townsend and Jordan Mousley. This does not cause the deer any pain.
How do you smooth out deer antlers?
Sand the deer antler with fine grit sandpaper to remove rough edges and smooth the ends of the antler.
How do you cut antlers for dogs?
Once you’ve confirmed the freshness of your antler, it’s time to make it more “dog-friendly.” Using hand and power tools, click, snip or saw the pointy ends of your antlers off, and sand down rough surfaces to avoid anything that could puncture or irritate your dog’s mouth.
Is deer antler dust toxic?
Each exposure may not be dangerous on its own, but combined exposures over the course of your life can really build up and cause problems. Yes.
Can you harvest antlers from roadkill?
Salvage Permits For Roadkill Deer Most states will offer what is called a salvage permit for a person that hit and damaged their vehicle in a collision with a deer or other big game animal. This salvage permit allows the person to legally possess the deer, from its meat to the antlers.
Is it illegal to cut antlers off a dead deer in California?
Answer: There is no provision in the Fish and Game Code prohibiting someone from picking up a set of antlers attached to a skull and carcass found on public land.
Is it illegal to cut antlers off roadkill in Illinois?
It’s illegal to kill the deer yourself. In this situation, a call should be placed to the non-emergency line of the nearest law enforcement or Illinois conservation police office to put down the injured animal. If you love venison so much that taking off the street (literally) how do you know it’s safe to eat?