To make the proper cuts; you’ll need to install the correct blade, which means you’ll need to know not only how to change the band saw blade, but also how to adjust the saw to keep the blade that you do install tracking straight and true. In the following step-by-step tutorial, learn how to change your band saw blade as well as how to make the adjustments necessary to keep your band saw blade cutting properly. Before you can begin to truly tension and adjust the tracking on your new band saw blade, you’ll need to loosen the band saw guide blocks and rollers that keep the blade tracking properly.
Speaker: Today, I’m going to walk you through the process of changing a band saw blade. It’s pretty simple, but there are three main things to consider: blade tracking, blade tension, and guide adjustment. Since the blade is a continuous loop, the table is slotted so that you can get the blade out.
The rear blade guard wraps the bandsaw blade while protecting you in the event of blade rupture. All most all bandsaw problems are blade related and a dull blade can cause blade drift. Knowing how to change a bandsaw blade can easily help you get rid of these problems quickly.
The most important step in changing bandsaw blades is to unplug the power to the bandsaw. At this point you can open the wheel doors to look inside …. … but before you start taking the blade off, you will need to take that bold or other holding mechanism from the bandsaw’s split table because there is no way of taking a bandsaw blade off without taking it through that split. Installing the blade is almost identical to taking it off, but this time you WILL need to re-adjust the upper and lower blade guides and the Thrust Bearing. So install the new blade by placing it on the upper wheel first, then the lower wheel, and now is a good time to take up a bit of slack in the blade. Before you start to align the blade on the wheel, make sure none of guides or thrust bearings are touching the blade … now, spin the upper wheel while adjusting the angle of the blade. The angle of the blade is adjusted usually with a locking knob on the upper back of the bandsaw. Turn the bandsaw on to make sure there is no sounds of the wheels or blade rubbing on anything.
Whether you’re a beginner or could just use a refresher, we’re going to walk you through the process for a perfect bandsaw blade adjustment setup every time, no matter what blade you install. Lower the upper blade guide, open the wheel housing(s) and blade guard and carefully remove the blade. So it should be no real shocker that you’ll encounter conflicting schools of thought regarding blade placement on the wheels and how it affects blade “Drift”.
how to change bandsaw blade Related Question:
How often should you change a bandsaw blade?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
Can I put a wider blade on my bandsaw?
An 18-inch diameter wheel can use a 0.032-inch thick blade that is 3/4 inch wide. In general, thicker and wider blades will be the choice when sawing dense wood and woods with hard knots. Such wood needs the extra strength of a thicker, wide blade to avoid breaking. Thicker blades also deflect less when resawing.
What do you do with old bandsaw blades?
There is life for those old, broken, and dull bandsaw blades. Just cut the old blade into sections about 12″ long. Stack the pieces together, alternating the teeth so that they don’t touch their neighbors. Use either same tape, or just braze the ends together,.
Are bandsaw blades worth sharpening?
Since a carbide-tipped bandsaw blade will cost well over $100, spending a third of the cost of the blade (or more) to get it sharp and working like new again can make financial sense. However the majority of bandsaw blades, the Wood Slicer included, are not worth spending money to have sharpened.
How much tension should a bandsaw blade have?
For carbon steel toothed blades (cutting blades) this is typically 15,000 to 25,000 PSI. Slitting type blades typically are tensioned in the range of 12,000 to 20,000 PSI. In general bandsaw blades are never tensioned past 35,000 psi.
What causes bandsaw blade drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
Is more TPI better?
Woodworkers quickly learn that the number of teeth-per-inch (TPI) on the blade has a big impact on the quality of a cut. The general rule of thumb is “the more TPI, the smoother the cut.” The true answer, however, is just a little more complicated than that, as you’ll learn once you understand how saw teeth work.
How many TPI does a bandsaw blade need?
For general wood cutting duties in typical 3/4″ material, use a 4 TPI blade for coarse, fast cutting and a 14 TPI blade for slower, smoother cutting. A blade in the 6 to 8 TPI range provides good general-purpose performance.
How thick of wood can a bandsaw cut?
Band saws are the undisputed champ when it comes to cutting curves and slicing through thick material. Many small band saws can slice though lumber a full four inches thick, and bigger saws handle six-inch cuts.
How long is a shopsmith bandsaw blade?
The Shopsmith Bandsaw accepts continuous- loop blades 72″ long and 1/16″-5/8″ wide. Shopsmith offers a variety of blades from 1/ 16″ wide to 5/8″ wide for cutting wood, plas- tics and nonferrous metals. To use a 1/16″ blade with the Bandsaw, you must install and use Cool Blocks (Part No.
How many times can a bandsaw blade be sharpened?
It often makes sense to replace a dull blade with a new one, but you can sometimes get the best value out of merely sharpening an old blade instead of replacing it altogether. You should typically be able to get two to three sharpenings before you need to change your blade completely.
Can Diablo blades be sharpened?
To ensure your Diablo cutting tool continues its high performance standards, please contact one of our approved “Authorized Sharpening Service Centers”.
How do I know if my bandsaw blade is sharp?
Get a 6 tooth per inch blade. When it gets dull,it will begin to not cut easily,and will sort of jerk along through the wood as you apply pressure. A sharp blade cuts without urging.
Why do my bandsaw blades keep breaking?
Machine Defects Even the best blades can fail if there is something else wrong with your bandsaw, and even a small misalignment of bearings or guides can put a twist in the blade as it goes around. Resulting in tension being applied in all the wrong ways which will lead to early breakage.