Re-sawing a board into thin, pliable pieces allows you to create curved shapes by bending and gluing the pieces around a form-a process called “Bent lamination.” Marking the board with the cabinetmaker’s triangle allows you to reassemble the thin pieces as they came from the board, so the lamination closely resembles a single piece of bent wood. Partially re-sawing a board on your table saw makes re-sawing with your band saw easier, because the blade has less to cut and the saw kerfs keep it from wandering. It’s a great method to use if your band saw bogs down during full-width re-sawing, and in many cases, it can save time by allowing you to re-saw without installing a re-saw blade.
To get started with resawing, I recommend a band saw of sufficient power and with a large depth of cut. “And, speaking of saw blades: the rule of thumb for resawing is “The wider the better.” Wider blades, 1/2″ and larger, cut straighter, which is the goal. Even if you don’t opt for a “specialty” resaw blade, stick with a wide and open-toothed blade to enhance your resawing activity.
Almost all U.S. woodcutting bandsaw blades over 1/2″ wide are made of coil stock. Every bandsaw blade, unless there’s something seriously wrong, can cut straight lines, but each will do so in its own way. The way the blade bowed tells you how to fine tune your fence for very precise resawing.
I’ve had perfectly acceptable results resawing with bimetal blades and great results resawing with silicone-carbide, low-tension blades. Drift varies from blade to blade, so follow this simple setup procedure every time you change blades. Because bearings can be used in contact with the blade, they can help the blade run straighter, resulting in less drift.
So I thought it would be useful to write a short article about the physics of bandsaw resawing and how to prevent the blade from wandering. To illustrate some of the concepts, I made a simple “Model” of a bandsaw blade cutting through wood. Even 1/2″ wide blades have enough beam strength for resawing if sufficiently tensioned.
The amount of drift varies with every blade, but you can compensate for it by clamping your fence to match the drift angle. SINGLE-POINT FENCE. Another way to overcome blade drift is to use a single-point fence like the one shown in the left photo above and in the margin. SETTING THE FENCE TO COMPENSATE FOR BLADE DRIFT. FEED RATE & TECHNIQUES. With either style of fence, your saw will help you determine the feed rate for resawing.
how to resaw on bandsaw Related Question:
What size bandsaw do you need for resawing?
To get started with resawing, I recommend a band saw of sufficient power and with a large depth of cut. Any motor smaller than 1hp and depth of cut less than 10″ will limit your effectiveness. (Some 14″ band saws have about a 6″ maximum cutso you’d be limited to a 12″ wide book-matched panel or less.)
What is resaw capacity on a bandsaw?
The resaw capacity is the maximum height (thickness) that can be cut. For the small shop furniture maker, go with 14″ as the minimum for a bandsaw, though 16″ is better. Those doing larger work might even want 18″ or 20″ machines. Just make sure you have a minimum resaw height of 12″ for versatility.
Can any bandsaw resaw?
Just about any bandsaw will do acceptable resawing. For example, all the cuts made in this story were done on an inexpensive, 14-in. bandsaw with a 3/4-hp motor. All we did to the saw was add a riser block to increase its capacity.
What bandsaw blade is best for resawing?
Resawing involves making rip cuts in the face of a wide board. So just like you would on the table saw, you’ll want to select a blade with fewer teeth per inch (TPI) than the blades you use for crosscutting or cutting curves. For most 14″ band saws, a 1 ⁄ 2 “-wide blade with 2-3 TPI is a good choice.
Can a band saw cut curves?
Whether it’s a tight curve or a closed opening, you can cut it on your band saw with a couple of easy tricks. Cutting on the band saw can be the same thing. The narrower the blade, the tighter the spots you can cut; in fact, some band saw blades rival a scroll saw for cutting tight curves.
How much tension should a bandsaw blade be?
For carbon steel toothed blades (cutting blades) this is typically 15,000 to 25,000 PSI. Slitting type blades typically are tensioned in the range of 12,000 to 20,000 PSI. In general bandsaw blades are never tensioned past 35,000 psi.
Can you resaw with a table saw?
When it’s time to resaw lumber for thin stock, a bandsaw usually comes to mind. But in many situations, such as preparing 1⁄ 4 “-thick stock for a project, you can do it on your tablesaw. Most 10″ tablesaws easily resaw boards up to 5 1⁄ 2 ” wide.
What does 14 mean on a bandsaw?
Rob Johnstone: Band saw sizes are derived from the diameter of the wheels in the saw. So a 14-inch band saw will have wheels that are 14-inches in diameter. There is another measure that indicates how wide a board you can resaw.
How much HP does a bandsaw need?
A 3/4 or 1 HP bandsaw is pefectly adequate for re-sawing stock at home….
What is a bandsaw jig?
Finger jigs are used to guide carefully made patterns on the bandsaw. The finger spaces the pattern just slightly away from the bandsaw blade, leaving a small amount of material to be worked by hand, or as I frequently do, shaped by a router outfitted with a flush-trimming bit.
How do I choose a resaw blade?
For resawing, use the widest 3-tpi skip- or variable-tooth blade your saw accepts. Typically, the wider the blade, the straighter it cuts. Cutting green (undried) wood requires the widest 2–3-tpi skip-tooth blade your saw accepts.
What is a resaw blade?
A resaw is a large band saw optimized for cutting timber along the grain to reduce larger sections into smaller sections or veneers. Resawing veneers requires a wide blade – commonly 2 to 3 inches (52–78 mm) – with a small kerf to minimize waste.