Band saw blade drift is a tendency of the blade to veer to the left or right while making a cut using the rip fence. The point of the last paragraph is that if the band saw is not set up properly and/or does not have a good quality, sharp blade installed and tensioned correctly, the chances of accurately adjusting for drift are minimal at best. Since there is little that we can do about blade drift at the blade, we adjust the fence to match the drift angle to essentially cancel it out.
The amount of drift varies with every blade, but you can compensate for it by clamping your fence to match the drift angle. SINGLE-POINT FENCE. Another way to overcome blade drift is to use a single-point fence like the one shown in the left photo above and in the margin. SETTING THE FENCE TO COMPENSATE FOR BLADE DRIFT. FEED RATE & TECHNIQUES. With either style of fence, your saw will help you determine the feed rate for resawing.
Being a happy bandsaw owner has a lot to do with your approach to coping with the fact that a bandsaw simply will not cut straight, or, in the sage words of veteran woodworkers, “Adjusting for drift.” Even the top performing 14″ bandsaw on the market, Powermatic’s 14 Bandsaw 1791216K, comes with a no-frills fence with 4 bolts on top rather than easy and obvious thumbscrews or knobs that say, “Adjust me here!”. Making the bandsaw cut nice and straight with this fence is a snap.
My playing around over the past few years seems to confirm the suggestion that presuming a correctly sharpened and jointed blade that can/has cut straight that the onset of drift is mostly to do with position of the blade on the tyres – that if a previously straight cutting blade starts to drift that it’s probably that the blade has moved on to a different part of the tyre. The other possibility is that something other than normal wear has happened to make the blade cut differently off one side than the other if a problem suddenly kicks in – but it should keep on tracking OK with normal even wear. Prime suspect with a new blade on a saw that has previously been OK has to be a misaligned weld, or a badly sharpened blade…. ian.
There’s no doubt about it – a bandsaw is one of the tools in your shop that might cause you the most frustration. Every shop needs one, so whether you’re an amateur struggling with blade drift or a professional who is constantly searching for ways to improve your workflow, having a well-functioning bandsaw is worth it. No matter what size your bandsaw is, we offer the always-reliable Timber Wolf bandsaw blades that make perfect replacements and cost-effective upgrades.
Ok ,, do me a favor and look at where your blade runs on the bottom wheel if you have the blade in the center of the top wheel. Then i will know what to expect tomorrow when i try out your method. I had always been told you adjust the fence to the saw.
how to avoid bandsaw blade drift Related Question:
Why does my bandsaw cut to the left?
When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
How much tension should a bandsaw blade be?
For carbon steel toothed blades (cutting blades) this is typically 15,000 to 25,000 PSI. Slitting type blades typically are tensioned in the range of 12,000 to 20,000 PSI. In general bandsaw blades are never tensioned past 35,000 psi.
Why are my bandsaw cuts wavy?
The clasic cause for wavy lumber is pushing a dull blade past it’s limits. Sharp don’t get it.
Why does my bandsaw mill blade wander?
When you’re sawing a soft wood with hard knots, the engine will slow down each time you hit a knot. If the blade speed drops below about 5000 FPM, the blade will start to wander. The governor will kick in to get the engine back up to speed but by the time that happens you’re through the knot.
Can a band saw cut curves?
Whether it’s a tight curve or a closed opening, you can cut it on your band saw with a couple of easy tricks. Cutting on the band saw can be the same thing. The narrower the blade, the tighter the spots you can cut; in fact, some band saw blades rival a scroll saw for cutting tight curves.
Why do my bandsaw blades keep breaking?
Machine Defects Even the best blades can fail if there is something else wrong with your bandsaw, and even a small misalignment of bearings or guides can put a twist in the blade as it goes around. Resulting in tension being applied in all the wrong ways which will lead to early breakage.
How long should a bandsaw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
Why does my bandsaw blade burn the wood?
A majority of issues with wood burning is because of a dull saw blade. These blades may not be sharp enough to efficiently cut the wood, and thus create enough friction to heat and burn the wood. What is this? Dull blades make it more challenging to cut, which causes friction as you pass the wood through.
What type of bandsaw blade is best for Resawing?
Resawing involves making rip cuts in the face of a wide board. So just like you would on the table saw, you’ll want to select a blade with fewer teeth per inch (TPI) than the blades you use for crosscutting or cutting curves. For most 14″ band saws, a 1 ⁄ 2 “-wide blade with 2-3 TPI is a good choice.
Is it worth it to sharpen bandsaw blades?
Since a carbide-tipped bandsaw blade will cost well over $100, spending a third of the cost of the blade (or more) to get it sharp and working like new again can make financial sense. However the majority of bandsaw blades, the Wood Slicer included, are not worth spending money to have sharpened.
Can bandsaw blades be sharpened?
If you’re looking to sharpen your band saw blade, you have two options: manually sharpen the blade yourself or use a mechanical sharpening machine.