A catalyst for this seems to be Jim Cummings article “Home Shop Bandsaw” in Fine Woodworking #63. From the hundreds of bandsaw owners I’ve talked with since the article appeared, it seems there are lingering questions on how to adjust a bandsaw blade, the blade choice and operation. “To find the correct tension, you can start with the tension scale on your saw, but you will probably need to fine tune the adjustment. With the saw unplugged, increase the tension on the blade until pushing on the side of the blade with your finger using a moderate amount of force deflects the blade about a 1/4” from its normal position. An interesting experiment is to set the side guys too far from the blade and notice how increased feed pressure and turning make the blade wander.
Even a low-end bandsaw blade tension meter can cost $300. If you use your bandsaw a lot or are doing delicate work, having the proper tension on the blade can be critical and the only way to accomplish this is with a bandsaw blade tension meter. With the bandsaw blade properly installed, and tensioned, and the blade guides properly set, the next issue is to make sure that the bandsaw table is square and level. We suggest that you go through the setup steps in this how to set up a bandsaw properly: the ultimate g guide before starting a new project and each time you change your bandsaw blade.
Install the blade and apply just enough tension to keep the blade securely on the wheels. Instead, tension the blade until your finger is only able to deflect the blade by about 1/4″. This test should be done at the back of the saw where nothing can get in the way of the blade. Adjust the thrust bearings carefully so that they do NOT rotate while the blade moves, but they DO begin to rotate as soon as light pressure is applied to the blade.
Blades with more teeth per inch will cut more slowly than a blade with fewer teeth, but will make a nicer cut. The material needs to be thicker than three teeth of the band saw blade being used. There are a variety of blades available; see Shop Staff for assistance, or refer to your bandsaw’s manual on how to change the blade.
Whether you’re a beginner or could just use a refresher, we’re going to walk you through the process for a perfect bandsaw blade adjustment setup every time, no matter what blade you install. Lower the upper blade guide, open the wheel housing(s) and blade guard and carefully remove the blade. So it should be no real shocker that you’ll encounter conflicting schools of thought regarding blade placement on the wheels and how it affects blade “Drift”.
how to adjust a bandsaw Related Question:
Why does my bandsaw cut crooked?
When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
Why do bandsaws wander?
If the wheels are worn and do not have a distinct top to the crown then the blade will not know where to go, and may wander around. This of course can cause poor cut quality and difficulty in setting the guides.
What causes bandsaw drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
How tight should a band saw blade be?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in. blade, I would set the scale to 1/2 in.
Why do bandsaws shake?
Band saw tires are another likely source of vibration. Tired tires, caked with pitch and dust or full of cracks and missing chunks, can not only contribute to blade and saw vibration but can also cause major blade tracking problems.
What is the set on a bandsaw blade?
The pattern of tooth setting is “left/right/straight,” where the left and right teeth are for opening or cutting the material, and the straight one – the so-called raker tooth – is for removing sawdust from the timber. The recommended tooth-set values are different for each blade type and profile.
Why does my bandsaw blade wobble?
The blade on a saw left idle for long periods of time can leave an impression in the rubber tire which might cause erratic tracking. Purchase and install aftermarket replacement tires. (Search for “bandsaw tire” at woodcraft.com.) If you still see a back-and-forth motion, the culprit is probably the wheel itself.
Which way should the teeth face on a bandsaw?
Installing A Bandsaw Blade Make sure the teeth point downward.
Why does my bandsaw blade burn the wood?
A majority of issues with wood burning is because of a dull saw blade. These blades may not be sharp enough to efficiently cut the wood, and thus create enough friction to heat and burn the wood. What is this? Dull blades make it more challenging to cut, which causes friction as you pass the wood through.