Install the blade and apply just enough tension to keep the blade securely on the wheels. Instead, tension the blade until your finger is only able to deflect the blade by about 1/4″. This test should be done at the back of the saw where nothing can get in the way of the blade. Adjust the thrust bearings carefully so that they do NOT rotate while the blade moves, but they DO begin to rotate as soon as light pressure is applied to the blade.
This how to set up a bandsaw properly is the ultimate guide to getting your bandsaw to perform to its full ability. With the bandsaw blade in place on the wheels, it is time to tension the bandsaw blade. Even a low-end bandsaw blade tension meter can cost $300. If you use your bandsaw a lot or are doing delicate work, having the proper tension on the blade can be critical and the only way to accomplish this is with a bandsaw blade tension meter. The wheels on your bandsaw must be both parallel and co-planar for the bandsaw blade to track properly and give straight even cuts. The upper set can be adjusted up or down so that you can adjust the distance from the upper blade guide to the top of the material you are cutting. With the bandsaw blade properly installed, and tensioned, and the blade guides properly set, the next issue is to make sure that the bandsaw table is square and level. We suggest that you go through the setup steps in this how to set up a bandsaw properly: the ultimate g guide before starting a new project and each time you change your bandsaw blade.
Whether you’re a beginner or could just use a refresher, we’re going to walk you through the process for a perfect bandsaw blade adjustment setup every time, no matter what blade you install. Lower the upper blade guide, open the wheel housing(s) and blade guard and carefully remove the blade. So it should be no real shocker that you’ll encounter conflicting schools of thought regarding blade placement on the wheels and how it affects blade “Drift”.
A catalyst for this seems to be Jim Cummings article “Home Shop Bandsaw” in Fine Woodworking #63. From the hundreds of bandsaw owners I’ve talked with since the article appeared, it seems there are lingering questions on how to adjust a bandsaw blade, the blade choice and operation. “To find the correct tension, you can start with the tension scale on your saw, but you will probably need to fine tune the adjustment. With the saw unplugged, increase the tension on the blade until pushing on the side of the blade with your finger using a moderate amount of force deflects the blade about a 1/4” from its normal position. An interesting experiment is to set the side guys too far from the blade and notice how increased feed pressure and turning make the blade wander.
A bandsaw will only cut accurately if the blade guides are set correctly, so these are important. Some people have the bearings touching, others don’t, we tend to side with the latter and like them to be set around 0.5mm either side of the blade. Simply place the Buddy up against the blade, using the recess to counter the tooth set.
how to set bandsaw blade Related Question:
Where should a bandsaw blade sit?
Make sure the machine is disconnected from the power supply. When tracking, you always want to make sure that the blade is sat on the crown of the wheel, with the deepest part of the gullet in the centre.
How close do you set the side guides on the band saw?
The front of the side guides should be located about 1/16″ back from the deepest part of the blade gullets. You don’t want the side guides to contact the cutting teeth of the blade since the teeth flare out at a slight angle. This adjustment is made to both the top and bottom guides.
Why does my bandsaw blade keeps coming off?
Blade Tension Is Too Loose The most common reason why the blade is slipping off is that there isn’t enough tension to keep it on. Blades can slowly become loose after years of wear and tear, and eventually, you’ll need to tighten or replace them.
Why is my horizontal band saw not cutting straight?
Make sure the blade is running in the correct direction. On machines powered by three phases power so it is common to get the wiring reversed and have the blade running the wrong direction. On all vertical blade bandsaws the working portion of the blade should go down. This forces the workpiece down into the table.
Which way should the teeth face on a bandsaw?
Installing A Bandsaw Blade Make sure the teeth point downward.
Why is it important to adjust the height of the blade guard on the bandsaw?
Adjust blade guard height to about 3 mm or 1/8 inch to 6mm or 1/4 inch above the top of the material being cut. Wider gaps will place tension on the blade and increase the risk of breaking. Ensure the blade is tracking correctly and runs freely in and against the upper and lower guide rollers.
How tight should a sawmill blade be?
For carbon steel toothed blades (cutting blades) this is typically 15,000 to 25,000 PSI. Slitting type blades typically are tensioned in the range of 12,000 to 20,000 PSI. In general bandsaw blades are never tensioned past 35,000 psi.
Why does my bandsaw blade wander?
Tim Inman: Because band saw blades ride on crowned wheels, they always have a little “camber” angle relative to the vertical axis of the wheel. This causes the blade to tip a little and makes the cut “pull” to the side.
Can a bandsaw blade be turned inside out?
Re: Turning a band blade inside out hi ,just get heavy gloves,an uncoiled blade ,step on the bottom and turn the blade inside out,and it will go right on a turner mill and just reverse the blade to sharpen. Thanks.
Why does my bandsaw blade wobble?
The blade on a saw left idle for long periods of time can leave an impression in the rubber tire which might cause erratic tracking. Purchase and install aftermarket replacement tires. (Search for “bandsaw tire” at woodcraft.com.) If you still see a back-and-forth motion, the culprit is probably the wheel itself.