Yes, the Starrett blades are fine quality, like anything Starrett makes. A 72″ 1/2″ x 3 or 4 tpi blade will cost you about $11. I get my bandsaw blades from Carbide.com, a small grind shop in Oxnard, CA. They are only 22 miles from me, but they have a nice web site and mail order business. McMasters has bandsaw blades, but they usually aren’t Lennox, and they are a little more expensive.
Advanz CG has a tungsten carbide grit bonded to an alloy back. It saw through many hard or abrasive materials that conventional tooth blades won’t cut. They are especially useful for cutting complex such as steel-belted tires, composite graphite, fiber-reinforced plastics and case-hardened steels.
06-30-2010, 1:48 AM #5 For me BS blades have gotten simple, for Carbide resaw blades the Laguna RK, for bi-metal and carbon blades 1/4″ or larger Lenox, for smaller than 1/4″ Starrett. Nothing wrong with a lot of the other blades I just see no reason to pay more when Lenox and Starrett are just as good or better and can be had cheaper. Also will the Craftsman take other lengths of blades – cannon find common store that sells 70 1/2″ blades.
17th December 2015, 10:05 AM #1 Starrett Bandsaw Blades I did a search and found nothing so forgive me if I have missed a previous thread. In my early days Starrett was synonymous with quality but I know that since then may brand names have been sold off and are now throw-away rubbish. The reason I bring this up is that I see a lot of Starrett bandsaw blades on eBay and they are a pretty good price. I have never purchased any high-end bandsaw blades so have no real comparison.
are starrett bandsaw blades any good Related Question:
Where are Starrett band saw blades made?
mt. airy, USa Manufactures band saw blades, other saw products and precision ground flat stock. Starrett-Webber Gage Cleveland, USa Manufactures gage blocks/standards and Starrett M-1® All Purpose Lubricant. Corporate headquarters athol, USa Manufactures the complete line of precision tools.
Is it worth it to sharpen bandsaw blades?
Since a carbide-tipped bandsaw blade will cost well over $100, spending a third of the cost of the blade (or more) to get it sharp and working like new again can make financial sense. However the majority of bandsaw blades, the Wood Slicer included, are not worth spending money to have sharpened.
How often should you change a bandsaw blade?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
Where are Starrett knives made?
The L.S. Starrett Company has been conducing business out of Athol, Massachusetts for over 140 years.
What is band saw blade?
A bandsaw (also written band saw) is a power saw with a long, sharp blade consisting of a continuous band of toothed metal stretched between two or more wheels to cut material. They are used principally in woodworking, metalworking, and lumbering, but may cut a variety of materials.
How do I choose a bandsaw blade?
Use coarse tooth blades (2 or 3 TPI) for re-sawing and cutting thicker materials. For general wood cutting duties in typical 3/4″ material, use a 4 TPI blade for coarse, fast cutting and a 14 TPI blade for slower, smoother cutting. A blade in the 6 to 8 TPI range provides good general-purpose performance.
Is more TPI better?
Woodworkers quickly learn that the number of teeth-per-inch (TPI) on the blade has a big impact on the quality of a cut. The general rule of thumb is “the more TPI, the smoother the cut.” The true answer, however, is just a little more complicated than that, as you’ll learn once you understand how saw teeth work.
How many times can a bandsaw blade be sharpened?
It often makes sense to replace a dull blade with a new one, but you can sometimes get the best value out of merely sharpening an old blade instead of replacing it altogether. You should typically be able to get two to three sharpenings before you need to change your blade completely.
What can I do with old bandsaw blades?
There is life for those old, broken, and dull bandsaw blades. Just cut the old blade into sections about 12″ long. Stack the pieces together, alternating the teeth so that they don’t touch their neighbors. Use either same tape, or just braze the ends together,.
How long do portable sawmill blades last?
Some can last under six months, and some can last years! Some of the most important variables to consider are what you are cutting, the condition of the machine and blade, how long you are using the blade, and even how you are feeding the wood through your saw as well.
What are Starrett knives like?
Designed for frozen food to temperatures of -76ºF (-60ºC), this blade has a high performance, providing fast cuts, with less waste in comparison to conventional blades. Starrett® Band Knives are made of High-Carbon Steel or AISI 420 Stainless Steel.
Where are Starrett tools made?
Starrett Made In America. Starrett has been making tools in the United States since the beginning. We were founded in Athol, Massachusetts in 1880, where our headquarters still remains. Since then, we’ve expanded to include other facilities in the states where we manufacture a variety of American-made products.
Is a wider bandsaw blade better?
The wider blades are stiffer overall (more metal) and tend to track better on the band wheels than narrow blades. When cutting thicker material, the wider blade has less ability to deviate because the back end, when in the cut, helps steer the front of the blade, especially if the side clearance is not excessive.
How do I know what size bandsaw blade I need?
In inches, determine the radius of each wheel, by measuring from the center to the outside of the wheel. Apply the following formula: (R1 x 3.1416) + (R2 x 3.1416) + (2 x C) = Saw blade length. Put a strip of tape on the floor to mark a starting point.
What is a 3h bandsaw blade?
Description. These are excellent-quality steel bandsaw blades that excel at ripping thick stock and resawing, and are also suitable for roughing blanks for carving or turning. The coarse 3 tpi hooked teeth power through hard woods and difficult grain, and have deep gullets for clearing sawdust.