There are nice deals on CL, and smaller tabletop drill presses can be had for $50 or so. I’ve got a generic import drill press that I’ve had for 30 years that still works fine. I realized that some of those I would have had to do a new saw also.
Drill presses are obviously cheaper, and I personally use it much more than I use a bandsaw; so I would chose a drill press. Been 30 years or so)…But I use one of my THREE DRILL PRESSES much more then I use my ONE bandsaw… Your requirements may be completely different then mine…I would hate to be without either…but I WOULD NOT give up my l drill press… Lots of luck… Bob Griffiths Bandsaw. I have the Ryobi 12″ benchtop drill press and use a MSC horizontal/vertical bandsaw and a Delta 3 wheel benchtop bandsaw.
If you want full 3/4″ panels you would want 4/4 or 5/4 stock from the umber yard to yield flat true 3/4″ stock after milling. If you go with a bandsaw suitable for resawing you are free to use a much wider variety of stock. Get a bandsaw if you want more freedom and versatility in stock prep and selection.
band saw or drill press first Related Question:
When would you use the drill press?
Although drill presses are used mainly for drilling holes, they can also be used for enlarging holes with a boring tool or finishing holes with a reamer. With the aid of a special tapping attachment and a tap, they can produce threads in a hole.
Can a drill press be used for wood and metal?
The drill presses can be used with wood pieces or metal sheets of various lengths, widths, and types.
What should have occurred before you use the drill press?
Make sure a guard, shield or barrier is in place and functioning properly before starting work. Use a vacuum, brush or rake to remove cuttings. Remove burrs and chips from a drilled hole. When making deep holes, clean out the hole frequently.
What speed should I set my drill press?
Quick Summary: Some approximate starting advice is to set the spindle speed between 700-1000 rpms for steel, above 2000 for aluminum, and slow down from there if you get discolored chips or heavy drill bit wear.
Do I really need a drill press?
You’ll need a drill press to bore accurate holes for hanging pegs in the back board. Want to make some wooden toys? The twist bits, spade bits and hole saws used for this work perform much better and more accurately in a drill press.
What are the advantages of a drill press?
The drill press has significant advantages over the hand-held drill, the principal one being accuracy. Its design means that it will drill at precise angles to the workpiece (usually ninety degrees); and it will drill holes of identical size and depth and position as many times as you wish.
Can you use a spade bit in a drill press?
Spade bits can be used both in a drill press or a hand-held drill, and there are two ways to regulate hole depth when you’re drilling by hand. If you only need to ballpark hole depth, then wrap a piece of electrical or masking tape around the shank.
What does 8 inch drill press mean?
Size Matters The size of a drill press is measured in terms of “swing,” which is defined as twice the throat distance (the distance from the center of the spindle to the closest edge of the column or post). For example, a 16-inch drill press will have an 8-inch throat distance.
Why do you need a drill press vise?
A drill press vise is a device designed to secure a workpiece firmly enough between its jaws that it won’t move at all when the drill bit is pressed into it.
Are band saws useful?
A band saw can be used to cut curves, even in thick lumber, such as in creating cabriole legs, to rip lumber and to crosscut short pieces. The most common use for the band saw, however, is in cutting irregular shapes. The second most common use is in resawing or ripping lumber into thinner slabs.
What is the purpose of a band saw?
A bandsaw (also written band saw) is a power saw with a long, sharp blade consisting of a continuous band of toothed metal stretched between two or more wheels to cut material. They are used principally in woodworking, metalworking, and lumbering, but may cut a variety of materials.
Can a band saw cut curves?
Whether it’s a tight curve or a closed opening, you can cut it on your band saw with a couple of easy tricks. Cutting on the band saw can be the same thing. The narrower the blade, the tighter the spots you can cut; in fact, some band saw blades rival a scroll saw for cutting tight curves.
How should you never stop the drill press?
19. Never stop the rotation of the drill chuck, spindle, or stock rotating on bit with your hands or fingers. 20. Don’t touch the drill bit and shavings since they are hot immediately after drilling.
What should you never use to remove drill shavings?
Remove chips with a brush, never by hand. Ease up on drilling pressure as the drill starts to break through the bottom of the material. Don’t use a dull or cracked drill.
What are the three important things to keep in mind when using a drill press not including operator safety and clamping work?
The radial-arm drill can support large, heavy castings and work can be done on them without the workpiece being moved. Name three important things to keep in mind when using a drill press (in addition to operator safety and clamping work). The three considerations would be speeds, feeds, and coolants.