Ive used mostly Carter blades on my 14 saw because I can get them super cheap through a friend but they dont make a true 1 resaw blade. 05-31-2018, 11:01 PM #3 I have the Laguna 18BX in my shop and after a lot of research went with the carbide 1″ Laguna Resaw King for resaw work and the bimetal Lenox Diemaster 2 blades for other duties. If the Lenox blade is a Woodmaster CT blade it is probably the best general resaw blade for the MM20 class of saw for speed, there are better blades for finish.
For resawing, the width of the blade should be close to the maximum the bandsaw will handle. On one forum, one person had great results with the Laguna Resaw King, but another person’s Resaw King blade broke, and Laguna said it was his fault for excess tension, even though they had refused to specify the recommended tension. Most bandsaw gauges don’t specify what thickness blade they are calibrated for, which is why they may be perfect for one blade, but are often misleading for other blades.
timberwolf vs laguna bandsaw blades Related Question:
What bandsaw blade is best for resawing?
Resawing involves making rip cuts in the face of a wide board. So just like you would on the table saw, you’ll want to select a blade with fewer teeth per inch (TPI) than the blades you use for crosscutting or cutting curves. For most 14″ band saws, a 1 ⁄ 2 “-wide blade with 2-3 TPI is a good choice.
What is the difference in bandsaw blades?
Bandsaw blades differ in thickness, width, length, and tooth configuration. Length varies by machine, but the size of your saw’s wheels typically determines thickness and width: Smaller machines (9–12″ wheels) need thinner blades to prevent breaking the welds. They also accept only narrow blades, often 1⁄ 2 ” or less.
What should I look for in a bandsaw blade?
Use coarse tooth blades (2 or 3 TPI) for re-sawing and cutting thicker materials. For general wood cutting duties in typical 3/4″ material, use a 4 TPI blade for coarse, fast cutting and a 14 TPI blade for slower, smoother cutting. A blade in the 6 to 8 TPI range provides good general-purpose performance.
Is more TPI better?
Woodworkers quickly learn that the number of teeth-per-inch (TPI) on the blade has a big impact on the quality of a cut. The general rule of thumb is “the more TPI, the smoother the cut.” The true answer, however, is just a little more complicated than that, as you’ll learn once you understand how saw teeth work.
How long should a metal bandsaw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
What causes bandsaw blade drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
What size bandsaw do I need for resawing?
To get started with resawing, I recommend a band saw of sufficient power and with a large depth of cut. Any motor smaller than 1hp and depth of cut less than 10″ will limit your effectiveness. (Some 14″ band saws have about a 6″ maximum cutso you’d be limited to a 12″ wide book-matched panel or less.)
Is a wider bandsaw blade better?
The wider blades are stiffer overall (more metal) and tend to track better on the band wheels than narrow blades. When cutting thicker material, the wider blade has less ability to deviate because the back end, when in the cut, helps steer the front of the blade, especially if the side clearance is not excessive.
What is the difference between hook and Raker bandsaw blades?
The difference is the shape of the teeth, which has a noticeable impact on how each type of blade performs. As the name suggests, the teeth on hook-tooth blades resemble hooks, raked aggressively forward.
How tight should my bandsaw blade be?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in. blade, I would set the scale to 1/2 in.
What is resawing on a bandsaw?
Bandsaw Resawing from the beginning: resawing is cutting a sawn plank of wood into thinner planks on a bandsaw. Thus the cut runs through the plank’s width, which distinguishes bandsaw resawing from ordinary bandsaw rip cuts where the blade runs through the stock’s thickness.
What size blade does a Milwaukee band saw?
Milwaukee Standard / Deep Cut Portable Band Saw Blades are designed to maximize performance of any portable band saw that takes a 44-7/8″ blade.
What does TPI mean on a bandsaw blade?
You must select the correct Teeth Per Inch (TPI) for the thickness of material you are cutting.
How many teeth per inch should a bandsaw blade have?
The number of teeth per inch (TPI) is important in obtaining the finish desired and the proper feed rate. A coarse tooth blade (2, 3 TPI) should be used for resawing wood and cutting thicker stock up to 8″. A fine toothed blade (18 to 32 TPI) should be used for thinner metals and plastics under 1/4″.
What does 32 TPI mean?
TPI is an acronym for Teeth Per Inch and is a common measurement to be detailed on saws. As a general rule, the more teeth per inch a saw has, the neater the finish will be, but the slower the saw will cut. The fewer teeth per inch, the faster the saw will cut but the rougher the finish will be.