A long straightedge should touch the tops and bottoms of both wheels simultaneously in order for the blade to track on the center of both wheels, photo below left. Reinstall the blade on the center of the tires and add tension while slowly turning the top wheel by hand. Hand-spin the wheels to check blade tracking and make any final adjustments before giving the blade a short test with the motor running.
Learn how to tune-up your Bandsaw for precision cutting. WOOD magazine’s Jim Heavey shows you exactly what to do. Whether you just bought your power tool or have been using it for years, a good calibration will ensure your cuts are true and accurate.
Learn how to tune up your band saw for top performance. You’ll learn how to change a band saw blade, clean a band saw, tension a band saw blade, adjust the band saw blade tracking, adjust the band saw upper and lower blades guides, and test the band saw cutting.
how to tune up your bandsaw Related Question:
Do I need to oil my bandsaw?
A band saw blade is a tool. You must lubricate both sides! In both cases, we know for a fact that lubrication of the body of the band increases band life by over 30%. Applied sparingly, you can cut grade lumber with NO staining to your product.
Why does my bandsaw blade keep coming off?
Blade Tension Is Too Loose The most common reason why the blade is slipping off is that there isn’t enough tension to keep it on. Blades can slowly become loose after years of wear and tear, and eventually, you’ll need to tighten or replace them.
Why do bandsaws shake?
Band saw tires are another likely source of vibration. Tired tires, caked with pitch and dust or full of cracks and missing chunks, can not only contribute to blade and saw vibration but can also cause major blade tracking problems.
What does the blade guard protect?
Its purpose is to keep the kerf of the cut open or “split” to prevent the workpiece from pinching the blade, or contacting the rear, rising teeth of the blade and thereby causing the blade to throw the workpiece back at the operator. This is known as “kicking back” the workpiece or simply a “kickback”.
What oil do you use for a bandsaw?
BAND SAW KLEENKOOL is a premium quality oil specially formulated for the unique problems associated with high speed band saws. BAND SAW KLEENKOOL is engineered to lubricate, cool, and clean residue from band saw blades.
Why does my bandsaw stall?
Using a dull blade or the incorrect type of blade can cause the band saw to cut through work pieces slowly. The blade will also move slowly through the work piece if the blade is installed incorrectly. A weak drive motor can also cause the band saw to cut slowly.
Can you lubricate a saw blade?
Luckily you don’t need much, just moisten your thumb and index finger on your tongue and run the blade up and down between them. If you need some lubricate for your saw blade but do not have any on hand, this is definitely your best bet. It doesn’t cost anything. Spit won’t cause premature blunting of your saw blades.
Why is it important to use lubricant when using the blade?
The lubrication system acts as a blade wash, removing the hairs. For many products lubricating the blade also greatly assists the cutting action and eases the passage of the blade through the extrusion. This will reduce blade wear & lessen the cutting power needed to cut the product.
How tight should my bandsaw blade be?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in. blade, I would set the scale to 1/2 in.
How tight should a sawmill blade be?
For carbon steel toothed blades (cutting blades) this is typically 15,000 to 25,000 PSI. Slitting type blades typically are tensioned in the range of 12,000 to 20,000 PSI. In general bandsaw blades are never tensioned past 35,000 psi.
How do you clean a meat band saw?
Clean the blades thoroughly using antibacterial soap or bleach and hot water to dislodge meat particles and germs that have clung to them. Sterilize by washing with hot water that is a temperature of 170 degrees.
Why is my bandsaw blade vibrating?
The tire was pulling the blade back and forth. If a urethane tire is not on the wheel straight, it will carry the blade back and forth, causing oscillation that is visible from the side of the blade.