Go look at a band mill and take notes of how its built then go from there. Whether you build, buy used, or buy new, one thing you will be glad you did, when you get into milling is going after the most h.p. you can afford. Milling softwoods can be done “Ok” on less power, but when you start chewing on oak or other hardwoods you will want all the poweryou can get, IMHO. Blazer yer home built mill looks pretty nice! Good job.
A 56-inch blade for cutting ties and wood is needed for an 18hp circular sawmill with that power factor. Based on contribution G, you can cut fast feeds at 10 grams per inch in addition to slow feeds at 5 grams per inch. If you have a fast 150 horsepower, you can run a machine quickly.
You can certainly saw with 13 HP, but you’ll have to go slow and too little power can affect results and blade performance. Get as much power as you can afford, especially if you plan on sawing bigger logs. Bite, cant face width, saw kerf, saw speed, wood type, tooth style and saw feed rate.
A modern high efficiency, high power factor 5 HP motor may not have substantially higher full load current than your old 2 HP motor. Baldor makes a good motor and so does Leeson, and I agree that a 5 hp would be a decent motor for that saw though a 7-1/2 will really keep those wheels spinning. “If you have a hard time believing this, consider this: back in the day I’m sure that the original users of your bandsaw also resawed up to 16” boards with the 2 HP motor that just gave out on you.
best engine for bandsaw mill Related Question:
Can you make money with a bandsaw mill?
A portable sawmill can be worth the investment. It can provide a source of wood for your own projects and give you a side business. For a source of lumber, as well as a profitable business, a portable sawmill can be a key piece of equipment on your farm.
How fast should a bandsaw mill run?
Bandsaw: Speeds. A common speed for the bandsaw is about one thousand feet per minute. Wood can effectively be cut at much higher speeds, up to and over five thousand feet per minute, but you should keep it slower because it’s safer.
What is the best blade for a sawmill?
9° Sawmill Blades – Ideal blade for lower horsepower (24HP and below) sawing frozen wood, hardwood, and small diameter logs. 10° Sawmill Blades – Very popular all-purpose blade for sawing mixed hardwoods such as red oak, cherry, walnut, soft maple, and poplar.
Is running a sawmill profitable?
It’s true that owning a sawmill can be a very lucrative business venture, and in the right circumstances it is not only possible but very likely to earn you a significant profit on a regular basis. However, it’s worth keeping in mind that building a business with only profit in mind is not sustainable in the long term.
How long does it take to get a WoodMizer sawmill?
And demand is high. “The lead time is 44 to 59 weeks right now for a sawmill,” says Kate Sebring, a sales representative for WoodMizer.
What is the best RPM for bandsaw?
Bandsaws always use 1725 rpm. The 3450 rpm are way too fast. From contributor R: Depending on the size of the wheels bandsaw blade speeds can vary between 2000 SFPM to over 4500 SFPM.
How long does a bandsaw mill blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
How fast should a sawmill blade run?
Re: Speed of band blade or Rpms Wood Mizer likes the blade to run at 5800 Surface Feet Per Min. The LT70 Super is the first mill for Wood Mizer than you can adjust the band speed through engine RPM. Frozen and extremely hard and dense wood MAY cut better with a slower band speed.
Where is Wood Mizer made?
Wood-Mizer is a sawmill manufacturer that also produces sawmill blades. Modern manufacturing facilities in Indianapolis and Batesville, Indiana USA and Kolo, Poland guarantee maximum quality at an affordable price anywhere in the world.
Are Norwood sawmills good?
How reliable are Norwood sawmills? Norwood has specialized in engineering and building portable sawmills since 1993. With tens of thousands of Norwoods hard at work in over 100 countries worldwide, they’ve proven that they’re reliable.
Are Norwood sawmills made in China?
I am serious about buying a mill and there is one advertised in Sydney that is, according to it’s seller, made in the same factory in China that makes the Norwood Lumber-Lite mills.
What kind of steel are sawmill blades?
Carbon steel is the most common metal used to manufacture sawmill blades and performs well for high production.
How thick is a sawmill blade?
Thinner plates can be used for lower density woods. If the plate is too thin, however, it will vibrate and the saw will wander in the cut. The plate of a circular saw blade is typically 1/8 inch to 1/4 inch thick.
How long should pine dry before milling?
Depending on the thickness of the lumber and where you live, weather and time of the year, it will take anywhere from 6 weeks to 4 months. Most lumber is in the 1” to 2” thickness and the time above applies to thicknesses. Drying cants, timbers, posts will take considerably longer.
Can you make money selling rough cut lumber?
When you first get a sawmill, the primary ways to make money are selling lumber or cutting for people. However, cutting for people is kind of tricky, because you’ll want to have some experience before you start doing that. If you’re cutting by the board foot and you take your time it doesn’t really matter too much.