Re-sawing a board into thin, pliable pieces allows you to create curved shapes by bending and gluing the pieces around a form-a process called “Bent lamination.” Marking the board with the cabinetmaker’s triangle allows you to reassemble the thin pieces as they came from the board, so the lamination closely resembles a single piece of bent wood. Partially re-sawing a board on your table saw makes re-sawing with your band saw easier, because the blade has less to cut and the saw kerfs keep it from wandering. It’s a great method to use if your band saw bogs down during full-width re-sawing, and in many cases, it can save time by allowing you to re-saw without installing a re-saw blade.
To get started with resawing, I recommend a band saw of sufficient power and with a large depth of cut. “And, speaking of saw blades: the rule of thumb for resawing is “The wider the better.” Wider blades, 1/2″ and larger, cut straighter, which is the goal. Even if you don’t opt for a “specialty” resaw blade, stick with a wide and open-toothed blade to enhance your resawing activity.
Almost all U.S. woodcutting bandsaw blades over 1/2″ wide are made of coil stock. Every bandsaw blade, unless there’s something seriously wrong, can cut straight lines, but each will do so in its own way. The way the blade bowed tells you how to fine tune your fence for very precise resawing.
I’ve had perfectly acceptable results resawing with bimetal blades and great results resawing with silicone-carbide, low-tension blades. Drift varies from blade to blade, so follow this simple setup procedure every time you change blades. Because bearings can be used in contact with the blade, they can help the blade run straighter, resulting in less drift.
The first step is giving your bandsaw a good tune-up to set the table perpendicular to the blade, get peak performance from the guides, and ensure the blade tracks true. “With your saw well-tuned, turn to the blade. Resawing wide boards requires a blade that cuts evenly throughout the stock’s thickness while evacuating large amounts of sawdust. The wider the blade, the straighter the cut, so use the widest blade your bandsaw can handle. Most saws accept at least a 1⁄2”-wide blade, and many even wider. Typically, a wide 3-tooth-per-inch blade provides the perfect blend of aggressive yet smooth cut and sawdust evacuation that resawing requires.
The amount of drift varies with every blade, but you can compensate for it by clamping your fence to match the drift angle. SINGLE-POINT FENCE. Another way to overcome blade drift is to use a single-point fence like the one shown in the left photo above and in the margin. SETTING THE FENCE TO COMPENSATE FOR BLADE DRIFT. FEED RATE & TECHNIQUES. With either style of fence, your saw will help you determine the feed rate for resawing.
best way to resaw on a bandsaw Related Question:
What type of bandsaw blade is best for resawing?
Resawing involves making rip cuts in the face of a wide board. So just like you would on the table saw, you’ll want to select a blade with fewer teeth per inch (TPI) than the blades you use for crosscutting or cutting curves. For most 14″ band saws, a 1 ⁄ 2 “-wide blade with 2-3 TPI is a good choice.
What size bandsaw do I need for resawing?
To get started with resawing, I recommend a band saw of sufficient power and with a large depth of cut. Any motor smaller than 1hp and depth of cut less than 10″ will limit your effectiveness. (Some 14″ band saws have about a 6″ maximum cutso you’d be limited to a 12″ wide book-matched panel or less.)
How much horsepower do you need to resaw?
A 3/4 or 1 HP bandsaw is pefectly adequate for re-sawing stock at home….
Can any bandsaw resaw?
Just about any bandsaw will do acceptable resawing. For example, all the cuts made in this story were done on an inexpensive, 14-in. bandsaw with a 3/4-hp motor. All we did to the saw was add a riser block to increase its capacity.
How many teeth do you need to resaw a blade?
Typically, a wide 3-tooth-per-inch (tpi) blade provides the perfect blend of aggressive yet smooth cut and sawdust evacuation that resawing requires.
How does a resaw guide work?
Resaw guides provide a higher level of control when adjusting for band saw blade drift. Curved face of the guide helps steer board into the cut. Easily attaches to the face of the band saw fence. This 7″ Resaw Guide is designed for larger capacity band saws.
What size bandsaw is best?
For a hobbyist, a 12″-14″ bandsaw is the ideal size. This size saw will provide plenty of power and a good deal of resawing capability. A professional will be better served with an 18″ bandsaw for a larger resawing capability. Choosing a 14″ band saw would provide plenty of power in a smaller footprint.
How much power does a bandsaw need?
Most home-level models incorporate a 3/4 to 1 horsepower motor, whereas professional models will have larger motors with variable speeds. For woodworkers, the variable speed won’t really matter, as slower than max speeds should be incorporated when cutting metals and some hard plastics.
What is the throat on a bandsaw?
The throat is the distance from the blade to the vertical frame section of the body of the saw. This distance determines the width of cut that can be completed on the band saw. The throat on a free-standing cabinet band saw typically exceeds the 12 to 14-inch throat of smaller, bench-top models.
Is a wider bandsaw blade better?
The wider blades are stiffer overall (more metal) and tend to track better on the band wheels than narrow blades. When cutting thicker material, the wider blade has less ability to deviate because the back end, when in the cut, helps steer the front of the blade, especially if the side clearance is not excessive.
Can I put a wider blade on my bandsaw?
An 18-inch diameter wheel can use a 0.032-inch thick blade that is 3/4 inch wide. In general, thicker and wider blades will be the choice when sawing dense wood and woods with hard knots. Such wood needs the extra strength of a thicker, wide blade to avoid breaking. Thicker blades also deflect less when resawing.
What should I look for in a resaw blade?
The article analyzed the most important features that help determine the performance of a resawing blade, namely blade thickness, blade width, number of teeth per inch, tooth form and durability.
What causes bandsaw drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
Why does my bandsaw blade twist?
The difference between the steak and the bandsaw is where the steak knife is short and thick, the bandsaw blade is generally long and skinny. This becomes a problem because it is possible to push hard enough on the blade to cause it to twist left or right.