Logan has some great tips and techniques for turning smaller logs into usable boards using the band saw in your shop. “Making Boards. After cutting the reference faces, you can start making boards. How you plan to use the wood will determine how thick to cut the boards. Keep in mind that the wet, rough-cut boards may warp and shrink. So don’t cut the pieces to the final thickness. Instead, I like to leave some extra material to allow for jointing and planing the wood smooth and flat once it’s dry. Adding about a 1⁄4” is a good rule of thumb. Freshly cut lumber needs to be stored and dried properly to end up as stable boards.
It’s surprisingly easy to mill short, small logs into furniture-grade boards, right in your own workshop, all without special equipment. “I’ve had good results using two methods for milling lumber from small logs in my shop. The simplest involves a hydraulic wood splitter – the kind used to turn logs into firewood. Clear, straight-grained, easily-split species of wood are easy to cleave into board-like billets. Most firewood splitters handle blocks up to 24” long, so when you find a good log, cut blocks to this length, even if you’re making your firewood shorter. “Regardless of how you mill your micro lumber, drying involves the same process used with other kinds of rough lumber. No matter how long it’s been since your logs have been cut, the wood is still too wet for woodworking if those logs have not been sawn into boards. That’s why you need to promote air circulation on all sides of every board, and a household fan really speeds progress. Stack your lumber with 1/2”-thick strips of scrap lumber between each piece, then direct air flow over the pile.
Cutting a log on the bandsaw I had the opportunity to go through some of the pieces of cut up firewood logs at my parents before they were split. If I use a really thin skillsaw blade, the table saw’s kerf will be about as wide as the bandsaw blade’s. In the past, I had no problems cutting though 12 cm thick dried maple with this blade.
I’ve had perfectly acceptable results resawing with bimetal blades and great results resawing with silicone-carbide, low-tension blades. Drift varies from blade to blade, so follow this simple setup procedure every time you change blades. Because bearings can be used in contact with the blade, they can help the blade run straighter, resulting in less drift.
George Vondriska provides tips on how to formulate the board foot measure of hardwood so that you can better assess how much wood you’ll need for your woodworking project and better communicate with the salesman when you go to purchase your wood. George Vondriska demonstrates how to use an Epilog laser engraver to cut templates and inlays in your shop. George Vondriska provides tips on how to use a backyard saw mill to cut lumber from logs for your woodworking projects.
how to cut logs into lumber with a bandsaw Related Question:
How do you cut wooden logs?
To cut your wood slices, we strongly recommend you have either a miter saw or band saw. These are the best saw options to use when cutting log slices, as they can make more precise cuts with the uneven nature of a log. They can also cut thicker pieces of wood than other types of saws.
How do I stop my log slices from splitting?
If your wooden slice was cut and left to dry for longer than a few days, use wood sealer as a soaking solution to help prevent cracks or splits from forming. Fill the container just over halfway so you can submerge the wooden slice without overflowing the container.
Can you cut logs with a circular saw?
Circular saws are great for cutting plywood and 2x’s, but you can also cut everything from logs to concrete to steel beams with the right blade or the right type of saw.
What are the three main ways to cut a log?
What many don’t know though is that there are three different method to cut wood to produce different results from the log and those are sawing, slicing, and using rotary.
Is milling your own lumber worth it?
Milling your own lumber can produce quality material for a fraction of the price of a lumber dealer. In fact, if you purchase your own mill, like I have, you can actually make a profit off of it by selling lumber to other woodworkers and by offering to mill other people’s logs.
How long do logs need to dry before milling?
Depending on the thickness of the lumber and where you live, weather and time of the year, it will take anywhere from 6 weeks to 4 months. Most lumber is in the 1” to 2” thickness and the time above applies to thicknesses. Drying cants, timbers, posts will take considerably longer.
Can you build with fresh cut lumber?
Building with green lumber for timber frame construction can save time, money and energy. With green timber, you can begin building right away without having to wait for the wood to dry, or having the added cost for kiln drying, which uses environmentally damaging fossil fuels during the drying process.