Bandsaw blades don’t last forever, but they are durable and can take on quite the workload. I wanted to learn more about how long these blades should last and how to extend the life of your blade. Keep reading below to discover more about how long your bandsaw blade should last. How long a bandsaw lasts depends mainly on the materials the band saw is used to cut, the condition of the blade and the bandsaw machine itself, how the materials are fed to the saw, frequency of usage, and maintenance.
Some can last under six months, and some can last years! Some of the most important variables to consider are what you are cutting, the condition of the machine and blade, how long you are using the blade, and even how you are feeding the wood through your saw as well. Others think that if you want your new blade to last as long as it can, investing in a higher-quality blade will be worth it in the long run. How you use your blade does make a difference in how long the blade should last.
A common question new sawyers ask is how much life they can expect from a band saw blade. First, the band saw blade is an amazing combination of steel alloys, precision sharpening, heat treating, and welding. The harder the wood, the shorter the time between blade changes-not only because hard woods tend to dull the blade more quickly, but also because it takes a sharper blade to slice through it.
How long a blade last depends on how dirty the logs are. Don’t get tunnel vision just by reading what the info says about how long a blade will last. For the most part most blades will get the job done, some faster and some slower, the blades you have described should get you close to 1000 bdft, there might be some waving with knots, but this will happen regardless of blades.
From contributor D: I run my blades about two clock hours but like the others, I can tell by the way my mill cuts and sounds if the blade is getting dull. On the average I would be ready to change blades after the third log. My mill is homebuilt and it’s a 2 minute change out on the blade so although it may not be advantageous for you to swap blades, for me it might be.
The knots in pine until you figure them out will cause the blade to dip or wavy cuts keep the blades clean of pitch and slow down a few inches before you get to the knots once in the knot you can speed back up. Some of my blades have less set than others because in hard wood to much set is hard on the blades and I don’t keep them separate so in green wood less set may slow them down. Have been sawing pretty steady, but not near what you had going through that many blades.
The blade is the standard 1″ silicon steel blade that shipped with my Laguna and I am trying to gage whether this is an appropriate life for a blade. 12-02-2008, 2:10 PM #2 Stock blades won’t last long. 12-03-2008, 7:39 AM #8 Timberwolf My Timberwolf blades last for years – if propertly tensioned before use and de-tensioned after use, if the feed rate is slow, if the blades are cleaned frequently, and cut only wood that has been inspected for metal objects such as nails or screws.
how long does a portable band saw blade last Related Question:
How many times can a bandsaw blade be sharpened?
It often makes sense to replace a dull blade with a new one, but you can sometimes get the best value out of merely sharpening an old blade instead of replacing it altogether. You should typically be able to get two to three sharpenings before you need to change your blade completely.
How long should a saw blade last?
They can last between 12 and 120 hours of continuous use, depending on the quality of the blade and material they’re used to cut.
How do you know if a bandsaw blade is bad?
Aside from visual signs like chipped blade teeth or rough cuts in material, you can hear when it’s time to replace a dull blade. As it goes bad, the saw blade forces the motor to work harder to cut through material, which causes a loud whining sound.
How long should a bandsaw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
Is it worth it to sharpen bandsaw blades?
Since a carbide-tipped bandsaw blade will cost well over $100, spending a third of the cost of the blade (or more) to get it sharp and working like new again can make financial sense. However the majority of bandsaw blades, the Wood Slicer included, are not worth spending money to have sharpened.
How often do you have to change blade on a sawmill?
When operating a band sawmill, a general rule is to replace the bandsaw blade with a sharpened one on average every 1,5 hours of cutting. In the case of cutting dirty wood, this time will be shorter.
How do you know when a saw blade is dull?
Look for worn-down, chipped, broken and missing teeth or chipped carbide tips that indicate it’s time to replace a circular saw blade. Check the wear line of carbide edges using a bright light and magnifying glass to determine if it’s beginning to dull.
Is more teeth on a saw blade better?
The number of teeth on the blade helps determine the speed, type and finish of the cut. Blades with fewer teeth cut faster, but those with more teeth create a finer finish.
Can saw blades be sharpened?
A good quality carbide blade can be sharpened 3-4 times before some or all the teeth need to be replaced and sharpening is a fraction of the cost of purchasing a new blade. As long as your blade is not warped or severely damaged, the correct answer is yes, the blade should be sharpened.
Do band saw blades get dull?
It happens from time to time. A blade seems suddenly to dull and then the drift. You should have ordered more in but you procrastinated and when you need a reasonably sharp blade you’re out.
Why does my bandsaw blade stop?
Using a dull blade or the incorrect type of blade can cause the band saw to cut through work pieces slowly. The blade will also move slowly through the work piece if the blade is installed incorrectly. A weak drive motor can also cause the band saw to cut slowly. First, check the installation of the band saw blade.
Why does my bandsaw mill blade wander?
When you’re sawing a soft wood with hard knots, the engine will slow down each time you hit a knot. If the blade speed drops below about 5000 FPM, the blade will start to wander. The governor will kick in to get the engine back up to speed but by the time that happens you’re through the knot.
What allows a saw blade to last longer?
Hang Circular Saw Blades Through the Center Hole Don’t let the blade’s kerf rest on the ground but hang a blade through its center hole for temporary storage. This can be as simple as a nail or screw in the wall, but at least the blade won’t be dulled by the floor or a shelf.
How long does a metal cutting blade last?
No matter how much care you give to your blade, a time eventually comes when it needs to be changed. On average, a typical cold saw blade should last at least six months. Damaged teeth.
How many teeth per inch should a bandsaw blade have?
The general rule of thumb is: For wood and soft materials aim for 3 – 6 teeth in the workpiece. For metals and harder materials aim for 6 – 24 teeth in the workpiece.