Band saw blade drift is a tendency of the blade to veer to the left or right while making a cut using the rip fence. The point of the last paragraph is that if the band saw is not set up properly and/or does not have a good quality, sharp blade installed and tensioned correctly, the chances of accurately adjusting for drift are minimal at best. Since there is little that we can do about blade drift at the blade, we adjust the fence to match the drift angle to essentially cancel it out.
Being a happy bandsaw owner has a lot to do with your approach to coping with the fact that a bandsaw simply will not cut straight, or, in the sage words of veteran woodworkers, “Adjusting for drift.” Even the top performing 14″ bandsaw on the market, Powermatic’s 14 Bandsaw 1791216K, comes with a no-frills fence with 4 bolts on top rather than easy and obvious thumbscrews or knobs that say, “Adjust me here!”. Making the bandsaw cut nice and straight with this fence is a snap.
The amount of drift varies with every blade, but you can compensate for it by clamping your fence to match the drift angle. SINGLE-POINT FENCE. Another way to overcome blade drift is to use a single-point fence like the one shown in the left photo above and in the margin. SETTING THE FENCE TO COMPENSATE FOR BLADE DRIFT. FEED RATE & TECHNIQUES. With either style of fence, your saw will help you determine the feed rate for resawing.
There’s no doubt about it – a bandsaw is one of the tools in your shop that might cause you the most frustration. Every shop needs one, so whether you’re an amateur struggling with blade drift or a professional who is constantly searching for ways to improve your workflow, having a well-functioning bandsaw is worth it. No matter what size your bandsaw is, we offer the always-reliable Timber Wolf bandsaw blades that make perfect replacements and cost-effective upgrades.
My playing around over the past few years seems to confirm the suggestion that presuming a correctly sharpened and jointed blade that can/has cut straight that the onset of drift is mostly to do with position of the blade on the tyres – that if a previously straight cutting blade starts to drift that it’s probably that the blade has moved on to a different part of the tyre. The other possibility is that something other than normal wear has happened to make the blade cut differently off one side than the other if a problem suddenly kicks in – but it should keep on tracking OK with normal even wear. Prime suspect with a new blade on a saw that has previously been OK has to be a misaligned weld, or a badly sharpened blade…. ian.
how to stop drift on a bandsaw Related Question:
What causes a bandsaw blade to drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
Why won’t my bandsaw cut straight?
Band Saw: Why won’t my band saw cut straight? When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
What is drift on a bandsaw?
Most band saw blades tend to veer slightly to the left or right when cutting. This is known as blade drift. The amount of drift varies with every blade, but you can compensate for it by clamping your fence to match the drift angle.
How tight should my bandsaw blade be?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in.
Why are my bandsaw cuts wavy?
Re: Band saw Cutting Wavy Cuts. The clasic cause for wavy lumber is pushing a dull blade past it’s limits. Sharp don’t get it.
Why do bandsaws wander?
If the wheels are worn and do not have a distinct top to the crown then the blade will not know where to go, and may wander around. This of course can cause poor cut quality and difficulty in setting the guides.
Why does my bandsaw blade wobble?
The blade on a saw left idle for long periods of time can leave an impression in the rubber tire which might cause erratic tracking. Purchase and install aftermarket replacement tires. (Search for “bandsaw tire” at woodcraft.com.) If you still see a back-and-forth motion, the culprit is probably the wheel itself.
Why does my bandsaw spark?
Ceramics can cause sparks. Or, if your thrust bearing is too far past the blade, more toward the center of the bearing than the edge, then it won’t turn and you’ll get sparks too, and possibly wear a groove in the bearing.
How long should a bandsaw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
Why do bandsaw blades break?
Machine Defects Even the best blades can fail if there is something else wrong with your bandsaw, and even a small misalignment of bearings or guides can put a twist in the blade as it goes around. Resulting in tension being applied in all the wrong ways which will lead to early breakage.
Is it worth sharpening bandsaw blades?
Since a carbide-tipped bandsaw blade will cost well over $100, spending a third of the cost of the blade (or more) to get it sharp and working like new again can make financial sense. However the majority of bandsaw blades, the Wood Slicer included, are not worth spending money to have sharpened.
How many times can a bandsaw blade be sharpened?
It often makes sense to replace a dull blade with a new one, but you can sometimes get the best value out of merely sharpening an old blade instead of replacing it altogether. You should typically be able to get two to three sharpenings before you need to change your blade completely.
Why is my bandsaw burning the wood?
A majority of issues with wood burning is because of a dull saw blade. These blades may not be sharp enough to efficiently cut the wood, and thus create enough friction to heat and burn the wood. What is this? Dull blades make it more challenging to cut, which causes friction as you pass the wood through.
How long does it take to get a WoodMizer sawmill?
And demand is high. “The lead time is 44 to 59 weeks right now for a sawmill,” says Kate Sebring, a sales representative for WoodMizer.
Which way should the teeth face on a bandsaw?
The teeth on the bandsaw blade should face down so that the cutting action is from the top of the material to the bottom.