“To find the correct tension, you can start with the tension scale on your saw, but you will probably need to fine tune the adjustment. With the saw unplugged, increase the tension on the blade until pushing on the side of the blade with your finger using a moderate amount of force deflects the blade about a 1/4” from its normal position. When too much tension is put on the blade, premature blade breakage and poor tracking can occur, but most important, you can damage your machine by trying to make it reach a blade tension greater than the machine was designed to operate at. The answer is yes, so be careful not to over tension your bandsaw blade.
On a machine with screw over spring tensioning, the most common on smaller machines, only really dependable way to set the blade tension is with a blade tension gauge. The machine manufacturer will provide a chart showing how much blade force is generated by any air pressure, and the blade tension in typical blade sizes. Over tightening the blade will shorten the life of the blade wheel rubber, bearings, and blade.
We’ve seen various methods for setting bandsaw blade tension, from fancy gauges to plucking the blade like a guitar string. Turn the tensioning handwheel until the tension gauge is at or a little above the recommended tension for your blade width. With the saw running, slowly release the tension-about 1⁄2 turn of the tensioning wheel at a time-until the blade starts to flutter, as shown at right.
Running your bandsaw blade tension too loose can cause your blade to come off track another dangerous situation. Then you adjust the bandsaw blade tension to reflect what the manufacturer recommends the blade tension should be. The bandsaw blade flutter test, my opinion probably one of the best ways to properly set up blade tension.
Installing the blade is almost identical to taking it off, but this time you WILL need to re-adjust the upper and lower blade guides and the Thrust Bearing. So install the new blade by placing it on the upper wheel first, then the lower wheel, and now is a good time to take up a bit of slack in the blade. Before you start to align the blade on the wheel, make sure none of guides or thrust bearings are touching the blade … now, spin the upper wheel while adjusting the angle of the blade.
Blade Tension Timber Wolf® Silicon steel blades are very stable at low tension or lower tension than what is normally recommended by most saw manufacturers and other blade manufacturers. If a specific cutting application requires that more tension be applied to the blade, such as when resawing large material or cutting green logs, the recommended force for these blades can be increased by as much as 20%. To apply the exact same blade tension each time saws would require a very expensive hydraulic or air strain tensioning system to create a repeatable tensioning method. Timber Wolf® blades from 1/8″ to 2-1/8″ for every cutting application; scroll cutting, curve cutting, ripping, cross-cutting,resawing, milling, metal cutting and Urethane Band Saw Tires.
Read on for help with your bandsaw blade tension settings. First, set your blade to the correct tension settings as this is ever so important. The result of excessive tension on the blade can cause tiny hairline cracks which lead to premature blade breakage.
tension on bandsaw blade Related Question:
How do you measure the tension on a bandsaw blade?
Bandsaw blade tension is usually worked out by measuring the elastic stretch (strain) of the blade under tension, and multiplying that by the Young’s modulus of steel and the blade’s cross-sectional aera to get the actual tension.
Why do I keep breaking band saw blades?
Even the best blades can fail if there is something else wrong with your bandsaw, and even a small misalignment of bearings or guides can put a twist in the blade as it goes around. Resulting in tension being applied in all the wrong ways which will lead to early breakage.
How do you tension a Timberwolf bandsaw blade?
Shut the motor or engine off and wait until the blade comes to a full stop. Add another 10% of tension to the blade by turning the screw-tensioner approximately 1/8 to 1/4 turn. The “flutter test” is now complete and you are now at appropriate tension for that particular blade.
Why is my bandsaw blade vibrating?
The tire was pulling the blade back and forth. If a urethane tire is not on the wheel straight, it will carry the blade back and forth, causing oscillation that is visible from the side of the blade.
How do I know if my bandsaw blade is tight enough?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in.
What is tension gauge?
Push & Pull Tension Gauge This is a multi-purpose dynamometer to measure compression and the competence tension of the measured object by using a head or hook.
How often do bandsaw blades break?
Some can last under six months, and some can last years! Some of the most important variables to consider are what you are cutting, the condition of the machine and blade, how long you are using the blade, and even how you are feeding the wood through your saw as well.