To make the proper cuts; you’ll need to install the correct blade, which means you’ll need to know not only how to change the band saw blade, but also how to adjust the saw to keep the blade that you do install tracking straight and true. In the following step-by-step tutorial, learn how to change your band saw blade as well as how to make the adjustments necessary to keep your band saw blade cutting properly. Before you can begin to truly tension and adjust the tracking on your new band saw blade, you’ll need to loosen the band saw guide blocks and rollers that keep the blade tracking properly.
Speaker: Today, I’m going to walk you through the process of changing a band saw blade. It’s pretty simple, but there are three main things to consider: blade tracking, blade tension, and guide adjustment. Since the blade is a continuous loop, the table is slotted so that you can get the blade out.
The rear blade guard wraps the bandsaw blade while protecting you in the event of blade rupture. All most all bandsaw problems are blade related and a dull blade can cause blade drift. Knowing how to change a bandsaw blade can easily help you get rid of these problems quickly.
Installing the blade is almost identical to taking it off, but this time you WILL need to re-adjust the upper and lower blade guides and the Thrust Bearing. So install the new blade by placing it on the upper wheel first, then the lower wheel, and now is a good time to take up a bit of slack in the blade. Before you start to align the blade on the wheel, make sure none of guides or thrust bearings are touching the blade … now, spin the upper wheel while adjusting the angle of the blade.
I presume you have chosen a new blade or just received a freshly sharpened band from the saw doctor! It is time now to fit your bandsaw blade. Loosely position top guides onto the band saw blade. I have made a video on how to change your bandsaw blade and setting up your guides.
how to replace blade on bandsaw Related Question:
Which way should the teeth face on a bandsaw?
The teeth on the bandsaw blade should face down so that the cutting action is from the top of the material to the bottom.
Why do bandsaw blades break?
Machine Defects Even the best blades can fail if there is something else wrong with your bandsaw, and even a small misalignment of bearings or guides can put a twist in the blade as it goes around. Resulting in tension being applied in all the wrong ways which will lead to early breakage.
What causes bandsaw blade drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
Why does my bandsaw blade keeps coming off?
Blade Tension Is Too Loose The most common reason why the blade is slipping off is that there isn’t enough tension to keep it on. Blades can slowly become loose after years of wear and tear, and eventually, you’ll need to tighten or replace them.
How long should a bandsaw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
Why does my bandsaw blade wobble?
The blade on a saw left idle for long periods of time can leave an impression in the rubber tire which might cause erratic tracking. Purchase and install aftermarket replacement tires. (Search for “bandsaw tire” at woodcraft.com.) If you still see a back-and-forth motion, the culprit is probably the wheel itself.
Why won’t my bandsaw cut straight?
Band Saw: Why won’t my band saw cut straight? When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
What do you do with old bandsaw blades?
There is life for those old, broken, and dull bandsaw blades. Just cut the old blade into sections about 12″ long. Stack the pieces together, alternating the teeth so that they don’t touch their neighbors. Use either same tape, or just braze the ends together,.
Is it worth it to sharpen bandsaw blades?
Since a carbide-tipped bandsaw blade will cost well over $100, spending a third of the cost of the blade (or more) to get it sharp and working like new again can make financial sense. However the majority of bandsaw blades, the Wood Slicer included, are not worth spending money to have sharpened.
Do bandsaw blades have set?
Re: set in bandsaw blade Set is important to keep the sides of the band from rubbing in the kerf and also to help guide the band so that it doesn’t follow the grain so bad. How much set depends on the type of wood, but it also depends on the thickness of the blade.
What is tooth set on a bandsaw blade?
The pattern of tooth setting is “left/right/straight,” where the left and right teeth are for opening or cutting the material, and the straight one – the so-called raker tooth – is for removing sawdust from the timber. The recommended tooth-set values are different for each blade type and profile.
Can a bandsaw blade be turned inside out?
hi ,just get heavy gloves,an uncoiled blade ,step on the bottom and turn the blade inside out,and it will go right on a turner mill and just reverse the blade to sharpen.
Are band saw blades directional?
On a typical wood or metal cutting blade the hook or of point of the blade should be pointing down for a vertical blade bandsaw, or for a horizontal blade saw the hook of the teeth should be pointed such that they enter the workpiece first as the blade moves.
What is the most common cause of a ruined band saw blade?
The most common reason for band saw blade failure is end of life due to wear of the cutting teeth, but also unnatural cutting characteristics, poor cutting surface and band or weld seam breakage.