“To find the correct tension, you can start with the tension scale on your saw, but you will probably need to fine tune the adjustment. With the saw unplugged, increase the tension on the blade until pushing on the side of the blade with your finger using a moderate amount of force deflects the blade about a 1/4” from its normal position. When too much tension is put on the blade, premature blade breakage and poor tracking can occur, but most important, you can damage your machine by trying to make it reach a blade tension greater than the machine was designed to operate at. The answer is yes, so be careful not to over tension your bandsaw blade.
Running your bandsaw blade tension too loose can cause your blade to come off track another dangerous situation. Then you adjust the bandsaw blade tension to reflect what the manufacturer recommends the blade tension should be. The bandsaw blade flutter test, my opinion probably one of the best ways to properly set up blade tension.
We’ve seen various methods for setting bandsaw blade tension, from fancy gauges to plucking the blade like a guitar string. Turn the tensioning handwheel until the tension gauge is at or a little above the recommended tension for your blade width. With the saw running, slowly release the tension-about 1⁄2 turn of the tensioning wheel at a time-until the blade starts to flutter, as shown at right.
T: TensionL: Free lengthμ: Linear density of the string : mass per unit length …. Tension is self explanatory: In the case of a guitar, you modify the tension of a string with the tuning keys and get the free string note. The linear density is what makes the strings sound different from eachother while keeping tension under certain levels – You don’t want the neck of your guitar broken or bent. You have to tighten the bandsaw blade until it vibrates at the frequency you got.
On a machine with screw over spring tensioning, the most common on smaller machines, only really dependable way to set the blade tension is with a blade tension gauge. The machine manufacturer will provide a chart showing how much blade force is generated by any air pressure, and the blade tension in typical blade sizes. Over tightening the blade will shorten the life of the blade wheel rubber, bearings, and blade.
Read on for help with your bandsaw blade tension settings. First, set your blade to the correct tension settings as this is ever so important. The result of excessive tension on the blade can cause tiny hairline cracks which lead to premature blade breakage.
how to adjust tension on bandsaw Related Question:
How much tension should there be on a bandsaw blade?
For carbon steel toothed blades (cutting blades) this is typically 15,000 to 25,000 PSI. Slitting type blades typically are tensioned in the range of 12,000 to 20,000 PSI. In general bandsaw blades are never tensioned past 35,000 psi.
Why does my bandsaw blade wobble?
The blade on a saw left idle for long periods of time can leave an impression in the rubber tire which might cause erratic tracking. Purchase and install aftermarket replacement tires. (Search for “bandsaw tire” at woodcraft.com.) If you still see a back-and-forth motion, the culprit is probably the wheel itself.
What causes bandsaw blade drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
Why is my horizontal band saw not cutting straight?
Make sure the blade is running in the correct direction. On machines powered by three phases power so it is common to get the wiring reversed and have the blade running the wrong direction. On all vertical blade bandsaws the working portion of the blade should go down. This forces the workpiece down into the table.
Why won’t my bandsaw cut straight?
Band Saw: Why won’t my band saw cut straight? When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
How tight should a metal bandsaw blade be?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in.
How much tension should a hacksaw have?
I would endorse the ‘finger tight plus three turns’ recommendation. It is important that the blade is taut. Also the angle of the saw when cutting is important, always use it by sloping the front end downwards, away from you, never upwards.
Why does my bandsaw bounce?
A lack of straightness in either the blade or weld could be causing the blade to bounce. Next, it is important to check the blade tension and make sure that it is high enough to keep blade bounce to a minimum. That way, your blade won?t take as much damage.