The circular saw is perhaps the most common saw owned by both professionals and DIYers alike. Even if you don’t practice the shot put with your tool, like dad did, chances are you’re not very delicate with the circular saw. Taking a few minutes for basic maintenance once in a blue moon, along with precautions like not throwing the most used power saw you probably ever had will keep it going and cutting true for years to come! For more tips, check out our other article on circular saw maintenance.
When lubing these Bosch and Skil saws, use only Bosch or Skil oils. Now, if when checking the oil, the existing oil in the saw is ultra-dirty or thick, you will need to entirely flush the bad oil from the saw. Remove the oil plug once more and invert the saw allowing the oil to drain completely from the reservoir.
how to lubricate circular saw Related Question:
Should you lubricate a circular saw?
On most saws, you don’t have to lubricate anything, that’s done during manufacturing. There are a few moving parts and a number of tools can be used to change the blade out. But even with such simple tools, there are still small maintenance things you can do to extend the life of your saw.
Can you use WD-40 on circular saw?
For additional protection against rust and corrosion, you can spray WD-40® Multi-Use Product on a cloth or rag and wipe on a thin coating of our classic formula to keep your tools looking good and help metal components to last longer.
What kind of oil do I use on a circular saw?
1.. I use GL-4 gear oil, and that’s what I use for all machinery gearboxes. More common gear oils are GL-5, and they can corrode brass or bronze gears. A circular saw will only see occasional use, so I would never pay $10 for 8 oz of Skil branded oil when I could spend less than that and get a gallon of good gear oil.
Can I use WD-40 on saw blades?
WD-40 Multi-Use is a great rust protection product and it will effectively protect your saw from building rust easily. Once you’ve got your hands on this product, go ahead and apply a thin and even coat on top of your saw blade and spread it using a clean and dry cloth. You can wipe off any excess with the same cloth.
What is the most important maintenance of a circular saw?
1 Avoid excessive moisture or humidity. Otherwise, the blades may rust and/or pit. 2 Keep the saw blades clean to maintain good performance. Accumulated pitch, sap, and other materials may dull the blade, require more push-through force, and generate increased levels of heat through friction.
Why does my circular saw keep jamming?
Here are some reasons your circular saw keeps stopping: Make sure your work piece is properly supported so it doesn’t pinch the blade which could also cause kickback in addition to stopping. Damaged, warped, loose or dull blade. Motor malfunctioning or overheating. Cable problems like frayed cord or weak connection.
Should you oil a saw blade?
Lubricate The Blade After each use, lubricate your blade with gun oil, paste wax, or WD-40 before storing. Gun oil or WD-40 can be wiped on with a rag. Paste wax should be wiped off after sitting on the blade for a few minutes. All of these choices prevent rust and help the saw blade slide through the wood.
Can you use a rusty saw blade?
The blade’s rusted surface can ruin the efficiency of the cutting teeth. In fact, a rusty blade may still be very sharp, but the exposed corrosion will cause the teeth to act as if they are dull. Clean saw blades are not only safer to operate, but they make a smoother cut.
Should a circular saw blade touch the guard?
Plunge Cut Instructions: Adjust the bevel setting to zero. Using the guard lever, lift the blade guard and start the saw. Rest the front of the base flat against the workpiece with the rear of the handle raised so the blade does not touch the workpiece.
When using a circular saw be sure to cut on the waste side of the cut mark to allow for the blades?
Never use a circular saw that does not have an upper blade guard because the. guard protects you from touching the blade. When using a circular saw,be sure to cut on the waste side of the cut mark to allow of the blade’s. Saws with fine blades that are excellent for delicate and intricate cutting are called.
What causes a circular saw to bind?
A circular saw binds because of failure to ensure proper blade depth; setting the blade too deep presents a danger because more blade surface is exposed while cutting than a properly set blade. When the saw is too deep, kickback and binding will be inevitable.
Why is my circular saw burning the wood?
Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty. If wood pitch resins build up behind the teeth of the blade, the cutting speed will slow down, increasing the chances for burns. Commercial blade cleaners are sold for this purpose.
Why does my circular saw stop mid cut?
Too much blade will become exposed to wood, and the blade can get stuck. Proper use can also be a culprit causing your circular saw to stop mid-cut. Make sure you are moving the saw in a straight line or using a jig to keep the cut straight.
Why is my saw blade smoking?
A Dirty Skill Saw Blade Can Cause Smoke When you use your saw repeatedly for an extended period, something called pitch can begin to coat the teeth of your blade. This pitch is rather sticky. As a result, it creates friction when cutting and possibly smoke.
How long do circular saw blades last?
They can last between 12 and 120 hours of continuous use, depending on the quality of the blade and material they’re used to cut.