NOTICE* The wide belt sander is a precise, powerful and expensive piece of machinery. Setups requiring anything other than the standard sander equipment must be approved by supervisor. Place piece onto feed belt so that it goes through the sander with the grain.
If you’re thinking of using a belt sander for the first time, there are a few safety tips you should follow to reduce the risk of bodily injury. Don’t forget to wear impact-resistant eyewear when using a belt sander. These are just a few safety tips to reduce the risk of injury when using a belt sander.
If your equipment is Not Under Warranty, or you acquired it from a source other than Shopsmith, contact a Shopsmith Tech Expert. We have created a special Shopsmith Engineering Support Line especially dedicated for Equipment No Longer Under Warranty. Calling our General Customer Care Line will allow you to have a Representatives schedule your Shopsmith Engineering Support Appointment so you don’t have to.
3 Do not operate the belt and disc sander without the instructor’s permission. 11 Belt sander roll end and side guards should be properly adjusted and in good condition. AT ALL TIMES – IF IN DOUBT, SEE YOUR INSTRUCTOR BELT AND DISK SANDER SAFETY BELT/ DISC SANDER DATA SHEET General Conditions Students must be trained on the safe and proper use of a Belt/ Disc Sander before they may begin using it.
belt sander safety rules Related Question:
What are the 3 most important sander safety rules?
Safety Rules Dust mask advised. Don’t wear loose clothing or gloves, keep long hair tied back. Never adjust Sander or setup while Sander is running. Never remove guard unless authorized by Technician or WRL Manager • Setups requiring anything other than the standard sander equipment must be approved by supervisor.
When using a belt sander you should never?
1. Do Not use the belt & disc sander if you are too tired, hungry, sad, mad, or dehydrated. Never work while under the influence of drugs, alcohol, or any medication that creates drowsiness or impaired thinking.
Should you wear gloves when using a belt sander?
Never wear gloves when using a belt sander. Many work gloves do not always fit tightly. This creates a situation where the gloves can actually become caught in the sander. You should always wear protection for your ears when using any type of power tool.
When changing sanding belts or discs what should be done to the belt disc sander?
When changing sanding belts or discs, what should be done to the belt/disc sander? Disconnect the machine from the electrical service. On most disc sanders the table can be adjusted ___________ degrees. 45.
How much weight should you apply to the belt sander while sanding?
No need to lean on the sander. Just let the weight of the machine do the work. When you get to the end of the board make sure the platen doesn’t cantilever too far past the edge. Allow 1/3 or less of the platen length to project over the edge.
How effective is a belt sander?
Because they have a lot of power and can handle coarse grits, they excel at the rapid removal of wood. Also, unlike orbital and vibrating sanders, the sanding action is linear, so even with coarse grits you can sand with the grain and get a good-looking result.
What PPE should you wear when using a belt sander?
What should you do to work safely with belt sanders? Wear safety glasses or goggles, or a face shield (with safety glasses or goggles). Wear a dust respirator for dusty operations. Make sure the sander is switched “OFF” before connecting the power supply.
Which piece of protective equipment should you always wear when using an electric sander?
Wear safety glasses with side shields or safety goggles, or a face shield (with safety glasses or goggles) when operating a sander. Wear hearing protection that is suitable for the level and frequency of the noise you are exposed to in the woodworking area.
What may happen if you use too much pressure on the sanders?
Avoid pushing down with too much pressure on the sander. However, doing this can cause issues like swirls, cut-through, uneven sanding and other problems, such as excess heat and loading.
Which of the following conditions should be avoided when operating a random orbit disk sander?
Wear a respirator or good quality dust mask when using the random orbit disk sander. 4. Never allow the rotating sanding disk to touch the electrical cord or any part of the body. Electrical shock or a serious cut may result.
What do belting sanding machines require at each nip point?
Belt sanding machines shall be provided with guards at each nip point where the sanding belt runs onto a pulley. These guards shall effectively prevent the hands or fingers of the operator from coming in contact with the nip points. The unused run of the sanding belt shall be guarded against accidental contact.
Why does my belt sander keeps breaking belts?
Heat, humidity, and age can contribute to belt seam failures, but they’re not the only causes. Check that your belts are turning in the direction indicated on the inside face. When not using your sander, release the tension on the belt.
What is better belt sander or orbital sander?
A belt sander is more effective for large materials, while the orbital sander is ideal for small spaces and pieces of furniture. A belt sander works effectively on flat surfaces, while an orbital sander can work with various angles.
Why do you need a belt sander?
Belt sanders are highly effective tools for removing roughness and preparing woodwork for less aggressive tools in the process like random orbit and finishing sanders. It is crucial to belt-sand with the wood grain rather than across it. Otherwise, the belt sander’s lateral action can ruin the work.
Can I sand a floor with a belt sander?
The handheld belt sander can sand off old finish and sand out dents and scratches much more easily than the previous sanders. While it won’t keep up with the speed of a normal floor sander, the hand held belt sander will get the job moving forward with reasonable speed.