“The length of the threaded studs mounted on the baseplate can be determined by placing the cutting wheel on the grinder and positioning the base plate for the thinnest wood likely to be joined with your biscuit joiner. In my case, I decided 1/2” wood is the thinnest I will need. In actual practice, it would be more difficult to bring your hand or fingers into contact with the cutting wheel on my biscuit joiner attachment than with a cutter wheel on a router bit. If I want to make biscuit slots for pieces in a polygon, I would need to make a wedge base of the proper angle to support the base plate of my biscuit cutter.
I think the biscuit joiner attachment that you had was made by Wolfcraft. I purchased a DeWalt biscuit joiner and never looked back. My personal opinion is that you should look for a good used dedicated biscuit joiner from DeWalt, Porter Cable, Bosch or other major tool name.
biscuit joiner grinder attachment Related Question:
What can I use instead of a biscuit joiner?
Some tests suggest a dowel joint will provide stronger joinery than biscuits. Tests also indicate that dowel joints are not as strong as tenon joints or dovetail joints. They do make solid and accurate joints, though. A dowel joint will be a better method than nails or screws and are much less susceptible to breakage.
What is the difference between a plate joiner and biscuit joiner?
A plate joiner is the same as a biscuit joiner and are used to create an oblong hole in two matching pieces of wood. After the joiners have created the hole, a biscuit is glued, inserted and typically clamped until the wood is dried.
Are biscuit joiners worth it?
Biscuits joints serve best as a quick and easy way to keep glue-up parts in alignment, and that they add appreciable pull-apart to strength joints that would be otherwise too weak to stand on their own – like butt joints and miter joints.
Can I use a router instead of a biscuit joiner?
If you want to make biscuit joints, you don’t have to buy a biscuit joiner. In most cases, a router equipped with a 5/32-in. slot bit can cut perfect slots to fit the biscuits. Mark the biscuit positions on both adjoining boards as you would with a biscuit joiner.
What are the disadvantages of a biscuit joint?
Biscuit joints do not stand up well against other joinery methods. We won’t spend any time comparing with mortise and tenon joints because all other joinery methods pale in comparison when measuring strength. But, as an example, the use of dowels as opposed to biscuits is a step up in strength.
What is the strongest type of wood joint?
Mortise and Tenon Woodworking Joints One of the strongest woodworking joints is the mortise and tenon joint. This joint is simple and strong. Woodworkers have used it for many years. Normally you use it to join two pieces of wood at 90-degrees.
Is a rebate joint as strong as a butt joint?
The advantage that the shoulder joint has over the butt joint is its strength as the rebate provides a much greater fixing area and, once glued, forms a solid corner. If you need even more strength in your joint you can combine the adhesive with screws, nails or even dowels that will further reinforce your corners.
Are dowel joints stronger than screws?
Dowel Strength Dowel joinery is stronger than screw joinery. The increased glue surface caused by the glue deeply penetrating the wood gives the dowel more holding power. The clamp and dry method used in dowel construction ensures that the joint is sufficiently set before the next step in building the item is taken.
How far apart should Biscuits be placed?
Biscuit Spacing Once you’ve determined the positions for the edge biscuits, you can calculate even spacing for the biscuits between the edges. Anywhere from 6 to 12 inches apart, measured on-center is usually sufficient.
Can you use a router sideways?
Yes you can use a router on a vertical surface.
Can you join plywood with biscuits?
However, with a biscuit joiner, clean, unobtrusive joints can be made in plywood, with no visible hardware and clean edges coming together. Whether joined together at 0 degrees, 45 degrees or 90 degrees, all joints are clean and tight, as well as being strong.
What tool is used to cut slots in wood for biscuits?
A biscuit joiner or biscuit jointer (or sometimes plate joiner) is a woodworking tool used to join two pieces of wood together. A biscuit joiner uses a small circular saw blade to cut a crescent-shaped hole (called the mouth) in the opposite edges of two pieces of wood or wood composite panels.
What is a rabbet joint?
A rabbet is basically just a groove or a dado on the edge of your wood piece that creates a lip. That lip can then fit snuggly into a groove. The rabbet joint is incredibly useful for furniture construction that uses panels, such as a small dresser. It’s also very useful for cabinet construction.
What makes a biscuit joint so strong?
The real magic of the mortise and tenon joint is that it takes this end grain to long-grain union and converts it to long-grain to long-grain, simply by inserting one piece into the other. As a result, the joint has a great deal of glue surface and strength.
How can butt joints be strengthened?
Butt joints should be reinforced with screws or nails to strengthen the joint. Typically, this reinforcement is done by driving the fasteners through one piece of stock near the end and into the end grain of the adjoining piece of stock.