Please check back later if you still haven’t found the answer you need. We would recommend replacing the carb and primer bulb which is Part Number: PS12116479 and the fuel line Part Number: PS9028916. It should be in the back position to put back on the cover.
240 husqvarna chainsaw parts Related Question:
What size chain does a Husqvarna 240 use?
3-Pack 18″ Semi Chisel Saw Chain for Husqvarna 240 Chainsaws – (18 inch, 3/8″ Low Profile Pitch, 0.050″ Gauge, 62 Drive Links, CSC-S62) – UpStart Components.
What size bar does a Husqvarna 240 have?
Amazon.com: HUSQVARNA CHAINSAW BAR 16″ 3/8″ 338XPT 317 240 235 : Patio, Lawn & Garden.
What is the H and L on a Husqvarna chainsaw?
1. Locate the idle-speed screw and the idle-mixture screws on the side of the chainsaw. According to the manual for the Husqvarna 51 available at ManualsLib, the idle-speed screw is labeled “T,” the low-speed screw is labeled “L” and the high-speed screw is labeled “H.”
Do Oregon chains fit Husqvarna?
Oregon M72 SpeedCut Chainsaw Chain for 18-Inch Bar -72 Drive Links – fits Husqvarna, Dolmar, Jonsered and more | Oregon Products.
Can you put a Stihl chain on a Husqvarna chainsaw?
Unfortunately, you won’t be able to use Stihl chains on Husqvarna saws because of the difference in pitch sizes.
What do you mix with Husqvarna chainsaw?
The correct mixing ratio for your Husqvarna is detailed in your product’s owner’s manual. But as a general guide, a fuel-to-oil ratio of 50:1 is recommended for Husqvarna products up to and including 75cc. That comes out to 2.5 fluid ounces of oil per 1 gallon of gas.
What is the difference between .325 and 3/8 chain?
The . 325 may be smaller and faster, but it may not be your best bet for your everyday needs. The three-eighths-inch chain is durable and lasts longer than its smaller cousin. This makes it one of the more popular switches for chainsaw users who want to get more out of their saw.
What is the T screw on a chainsaw?
The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed. L Screw – With the chainsaw still running, take a screwdriver and turn the L screw clockwise. Keep turning it until the engine almost stops turning.
How do I identify my Husqvarna chain?
The model number of a Husqvarna chainsaw is printed on the side of the recoil assembly on the unit(eg. 455, 460, 372 XP). Husqvarna chainsaws also have a small metal plate stamped with the model number, part number, and serial number. The plate is typically located in one of four locations.
What is the longest bar you can put on a Husqvarna 455 Rancher?
Re: Husqvarna rancher 455 w/24″ bar – durability? If you really want to break that monster down with a 20″ bar, you can. Just take a bit of cunning, and work. Make a vertical cut into the end of the log, about 19″ from the side, as far in as the bar reaches.
Can you use a Oregon bar on a Husqvarna chainsaw?
Oregon® 20 in. Chainsaw Bar & H78 Chain, Fits Husqvarna, Poulan, Makita, Craftsman, Jonsered, McCulloch and more (577330) | Oregon Products.
Where are Husqvarna bars made?
Husky bars are mostly made by Husky in Norway (not Sweden) or by Oregon in Canada/USA. Some have been made by GB in Australia in the past.
Are Husqvarna chainsaw bars any good?
Husqvarna 20 Inch Chainsaw Bar – Best Overall The Husqvarna 20-Inch Chain Saw Bar is built with heavy-duty, professional materials. It’s easy to install on many Husqvarna chainsaws, and is short enough to be portable. It has a high-performance, low-vibration chain that can be adjusted easily.
What is the H and L on a carburetor?
They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet).
Are all Husqvarna chainsaws 50 to 1 mix?
Things to Remember: All Husqvarna chainsaws use the ratio of 50:1, this means that for every gallon of gas you will use 2.6 oz. of 2 stroke engine oil. Even though your owner’s manual may say 87 octane, always use 89, just to be safe, and to prevent “knocking” which could be damaging to your engine.