340 husqvarna chainsaw parts Related Question:
What is the H and L on a Husqvarna chainsaw?
1. Locate the idle-speed screw and the idle-mixture screws on the side of the chainsaw. According to the manual for the Husqvarna 51 available at ManualsLib, the idle-speed screw is labeled “T,” the low-speed screw is labeled “L” and the high-speed screw is labeled “H.”
What is the T screw on a Husqvarna chainsaw?
The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed. L Screw – With the chainsaw still running, take a screwdriver and turn the L screw clockwise. Keep turning it until the engine almost stops turning.
What is the difference between .325 and 3/8 chain?
The . 325 may be smaller and faster, but it may not be your best bet for your everyday needs. The three-eighths-inch chain is durable and lasts longer than its smaller cousin. This makes it one of the more popular switches for chainsaw users who want to get more out of their saw.
Are .325 and 3/8 chains interchangeable?
You can replace a 3/8 Oregon PowerMatch nose with a . 325 PowerMatch nose on any length of Oregon PowerMatch bar you want. Then when you use up the . 325 chain just put the 3/8 nose and rim sprocket back on.
What size is Husqvarna fuel line?
At about 24” in length, this line is usually long enough to do more than just one fuel system and works on most, but not all Husqvarna (brand names also included are Poulan, Craftsman, and Weedeater) 2-cycle equipment. This is a 1/8 in. fuel line for a Husqvarna 142, very hard to find.
Why is gas leaking from my chainsaw?
The fuel tank on your chainsaw is a plastic reservoir that stores fuel. The plastic can occasionally become cracked, and when this happens, fuel can leak out. There are several places on the fuel tank that can cause leaks, such as the grommet, the gasket, or the fuel cap.
How do you fix a chainsaw that won’t stay running?
Clogged Air Filter – Check the air filter Your chainsaw’s engine needs the right supply of air to run properly. A clogged air filter can be the reason why your chainsaw won’t start or stay running. Find your chainsaw’s air filter and remove it. If it’s clogged or too dirty, wash it or replace it.
Why is it so hard to pull start my Husqvarna chainsaw?
If your chainsaw is hard to pull, here are some common causes: The pully system is snagged or stuck. The starter assembly is stuck or sticky. The housing may be damaged.
Why does my chainsaw cut out when hot?
When your chainsaw quits after it gets hot, you either have a problem with gas flow being restricted into the engine or with the spark. This is a common occurrence on older-model chainsaws. By replacing your spark plugs and keeping your gas lines clear you can reduce the chances of this problem recurring.
What does 325 mean on a chainsaw chain?
325″. Be aware that there are two types of chain that are both 3/8″ pitch, one is the “standard” type generally used on saws 55 cc and up, the other has the same pitch but is called “low profile” and is used on smaller saws – up to 45 cc or so.
How do I identify my Husqvarna chain?
The model number of a Husqvarna chainsaw is printed on the side of the recoil assembly on the unit(eg. 455, 460, 372 XP). Husqvarna chainsaws also have a small metal plate stamped with the model number, part number, and serial number. The plate is typically located in one of four locations.
Can I change the pitch on my chainsaw?
Yes, pitch does matter. If you change to . 325 chain you will also need to change the drive sprocket. If the saw has a floating rim then just change that, otherwise it is a new drum which may not be available.
What is the difference between full chisel and semi chisel?
The sharp corner of the full chisel cutters split wood fibers easily and provides the fastest, most efficient cutting in clean softwood. The corner of the cutters on a semi-chisel saw chain are slightly rounded.
What does the pitch mean on a chainsaw chain?
Chain pitch is the size of the chain and is defined as the distance between any three consecutive rivets divided by two. Oregon chain is made in several pitches – 1/4″ is the smallest, 3/8″ is the most popular, and 3/4” is the largest.
What is the H and L on a carburetor?
They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet).