Unless 4″ diameter wood is being cut, for a 12000 max rpm saw it’s not 12000 rpm, but anywhere from 7000 to 10000 rpm. The max torques for 050, 075(7000 rpm), 076(7000 rpm), 880(6000 rpm), and 660(6500 rpm) are all within 1000 RPM of each other so all these saws would work fine together. With the 660 and 880 the full HP of each saw would bot be realised because they don’t have an identical torque curves and their max HPs are not delivered at the same RPMs but they would still work fine together.
Part Number and name: G778-84 Alaskan Chainsaw mill, 84 inch. General description: Basic Mill and 84-inch Handle and Rail Set: Tubular Aircraft aluminum extrusion and zinc-plated steel parts. MADE IN THE USA. Use description: This versatile, heavy-duty chainsaw lumber mill accurately cuts planks and beams up to 70-78″ wide and 1/2″ to 13″ deep.
24″[61cm] Granberg Mk IV – Takes max bar size of 30″[76cm]; to give a max cut width of 22″[56cm]. 36″[91cm] Granberg Mk IV – Takes max bar size of 42″[107cm]; to give a max cut width of 34″[86cm] . 48″ [122cm]; Granberg Mk IV – Takes max bar size of 54″[137cm] to give a max cut width of 46″[117cm] . 60″[152cm]; Granberg Mk IV – Takes max bar size of 64″[162cm]; to give a max cut width of 56″[142cm] . 72″[183cm]; Granberg Mk IV – Takes max bar size of 74″[188cm] to give a max cut width of 68″[173cm]. 84″[213cm]; Granberg Mk IV – Takes max bar size of 84″[213cm] to give a max cut width of 76″[193cm].
84 inch chainsaw mill Related Question:
How big of a chainsaw do I need for an Alaskan mill?
Most Alaskan mills require at least 3 inches extra at the end of the bar for attachment. I also recommend going with a saw with an engine size of at least 60cc for smaller logs and softer woods. A minimum of 90cc would be best though.
Is chainsaw milling worth it?
A chainsaw mill is one of the most efficient and effective tools when it comes to converting wood into lumber. Lumber is a very effective raw material that can be used for a variety of purposes. Be it for firewood or be it for construction purposes, you can certainly utilize lumber for whatever you need.
How much does it cost to mill a chainsaw?
Re: How to charge for chainsaw milling It can be difficult to accurately figure board feet with natural edges, taper, crotches, etc. Around here, the common rate is $65-85 per hour.
Is it worth milling your own lumber?
Milling your own lumber can produce quality material for a fraction of the price of a lumber dealer. In fact, if you purchase your own mill, like I have, you can actually make a profit off of it by selling lumber to other woodworkers and by offering to mill other people’s logs.
Does skip tooth chain cut faster?
A skip chain has fewer cutting teeth than a conventional chain which means it won’t be dragging as many teeth through the wood you’re cutting. Less drag on the chain means less power is needed to cut through the log. That means the motor on your saw runs faster which keeps it in a more efficient power curve.
How well do chainsaw sawmills work?
A chainsaw has a saw kerf right around 3/8 of an inch, which means it is very inefficient and produces a lot of sawdust. For these reasons, a chainsaw mill is definitely not to be used for optimizing the amount of lumber that you can yield from a log.
What chainsaw do loggers use?
Stihl is the most popular chainsaw for professional loggers. It has a long-lasting chain, and you can also enjoy the exceptional cutting speeds available with this brand of chainsaw. Additionally, the chains are high-performance, low vibration, and quiet in their performance.
How long does it take to mill a log with a chainsaw?
In the world of chainsaw milling, the more powerful the saw the better. You can mill with a smaller saw; however, it’s going to be really slow. On average, it takes me about 10-15 minutes to make one cut using my saw, based on the size logs that I typically cut. Expect that a smaller saw will cut slower.
What size saw do loggers use?
Since you’re buying a professional chainsaw, you should look out for nothing less than 40CC and 1 HP engine power. Chainsaws with more engine power will be more powerful than those with less engine size. Those chainsaws with an engine size of 40 to 80 CC are often used by loggers that have to fell a lot of trees.
How much does it cost to mill lumber?
By the Board Foot Pricing varies by species and location but ranges from $0.25 to $0.50 per board foot of sawn lumber. This pricing method places all of the risk of productivity on the sawyer since the customer is only paying for the lumber they receive.
How do you price rough cut lumber?
For example: if you want to know how many BF are in a 4 x 6 x 10 you multiple that together: 4 x 6 x 10 = 240 and then divide that by 12, 240 / 12 = 20 BF. To determine the price, you multiple the BF by the price/BF, so in this case a 4 x 6 x 10 is $. 80/BF, so the price per piece is $16.00.
How long should a log sit before milling?
From Gene Wengert, forum technical advisor: As a rule of thumb, there will be a measurable loss in four to six weeks of warm (over 50 F) weather. It is just a rule of thumb.
How long do logs need to dry before milling?
Depending on the thickness of the lumber and where you live, weather and time of the year, it will take anywhere from 6 weeks to 4 months. Most lumber is in the 1” to 2” thickness and the time above applies to thicknesses. Drying cants, timbers, posts will take considerably longer.
How long should logs dry before being used to build?
You should seal the ends within minutes after being cut down; you should not wait hours, and definitely not days! The drying time will vary depending on the wood species and thickness of the logs, but they will take at least one to two years to dry – the longer you can leave them before you start building the better.
Why do Loggers Run chainsaw bars upside down?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.