Important: Always make sure the engine is turned off before you begin tensioning the chainsaw chain. Locate the chain tension adjustment points on your chainsaw. Common locations for adjustment points include the side cover and the front of the chainsaw.
Chainsaw chain tension should be checked and tightened often. A properly stretched chainsaw chain should be a little loose on the guide bar – but not so loose that you can pull the drive links out of the bar nose. Maintaining the proper chain tension is therefore essential because it ensures your chainsaw is safe to use and will last for years to come.
There are no formulas or concrete rules on how you should tighten your chainsaw chain. Bar oil is going to be consumed at a higher rate, and if the chain is too tight it can also damage the clutch and bearings when you start the chainsaw. A loose chain will simply flop around the bar grooves, and a chain that is too tight will refuse to budge.
After reading this post, you’ll know how tight a chainsaw chain should be, how to adjust it, and how to test that you’ve got it perfect. If you’re unable to pull the chain away from the bar, then your chain is too tight. If you keep trying to tension your chain and you just can’t get it right, you may have the wrong sized chain.
what is chainsaw lubricant Related Question:
What kind of oil do you use for a chainsaw bar?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
Can you use engine oil for chainsaw chain lubricant?
Instead manufacturer’s recommend summer and winter weights. If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Is bar and chain oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Can I use 5w30 for chainsaw bar?
Can I Use 5w30 for a Chainsaw Bar? Like 10w30 motor oil, you can use 5w30 oil. However, the thin and low-viscosity SAE5 weight oil will not cling to the chain and chainsaw bar very well in the summer. You may experience a lot of oil loss and a messy worksite if you choose this chainsaw bar oil alternative.
What is special about chainsaw oil?
Chainsaw bar oil has a certain level of “slickness” to it. This slickness keeps the chain spinning at a fast rate without getting slowed down by the friction that occurs when metal rubs against metal. So, if you want to use the “correct” type of bar oil in your chainsaw, consult the manual and use what it suggests.
Can you use 10w40 in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30. Thicker.
What is bar oil equivalent to?
Canola oil It is thinner than regular vegetable oil, meaning it will tend to fly off the chainsaw more quickly – but it has a more suitable viscosity at lower temperatures so makes a good substitute for chainsaw oil when it is too cold to use vegetable oil.
Can you use vegetable oil chainsaw?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
Can you use transmission fluid for chainsaw bar oil?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .
What kind of oil is chain oil?
The Standard. Petroleum-based bar oil has been the standard for chainsaws.
Can you use engine oil as bar oil?
It might be OK for a bit but I probably wouldn’t do it. You could look up your owner’s manual to see if they say anything. If you must use the chainsaw and have nothing else on hand, surely motor oil is better than nothing. I think bar oil is stickier than regular motor oil to prevent splattering as much.
Do you need bar and chain oil?
You want lubrication of the actual chain against the bar. You don’t want to chain to burn – which is what might happen if there’s too much friction. Without oil, it causes frictional force on the motor in the chainsaw as well.