I’m with you if you have a need for a big saw use one!Now I am all for getting buy with the lightest saw possible for the task at hand but personally any mods to a saw that your going to use for every day work beyond opening the muffler and properly adj. I have ran a Walkerized 346 along with saws from three other builders. The Walkerized saw was comparable to one, faster than one and slower than the other.
Bob Walker is one of the foremost saw customizers on the B.C. coast. Although Bob is now retired, he lends his expertise to Donny who carries on the production of the Walkerized Saw. Bob and Holly still pop into the shop to pass on their wisdom to all who enter the Walker’s Saw Shop.
what is a walkerized chainsaw Related Question:
What does the T mean on a chainsaw?
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs. The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed.
What does displacement mean on a chainsaw?
Chainsaw power is measured by displacement, which is the volume displaced by the piston in its upward stroke. Displacement is measured in cubic inches or centimeters. The larger the displacement, the more power generated by the explosion of the compressed fuel/air mixture that drives the piston.
What is considered a pro chainsaw?
Professional-grade chainsaws are the ones you turn to for engines with higher horsepower as well as higher torque for consistently elevated output. In order to contain and channel all of that power, the engines on professional saws are made with components designed to withstand long hours of use: Heavier bearings.
What are the different types of chainsaw?
There are four main chainsaw blade / cutter styles, these are; square chisel, full chisel, semi-chisel and low profile. But then there are some variations of these four styles on the market, that we also go into detail about below. Read on to see the main chainsaw blade styles and their applications.
Why does my Poulan chainsaw dies when I give it gas?
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
What is the LA screw on a Stihl chainsaw?
The LA setting on Stihl chainsaws is controlled by a screw on the outer housing of the engine that adjusts the flow of fuel and air through the carburetor. This screw is inside the engine housing on the carburetor, but is accessible through a hole or gap in the outer housing of the saw.
How many cc should a good chainsaw have?
Engine size is measured in cubic centimeters (cc) or cubic inches. In general, the bigger the number, the more powerful the engine. Most homeowners will do fine with a saw in the 32 cc to 45 cc range.
Is higher cc better in chainsaw?
Power, measured by cubic centimeters (cc), differentiates chainsaw engines. A larger engine with 65 cc generates more power, which is useful when sawing through tough trees. Smaller engines with just 31 cc, meanwhile, are all you need to trim your hedges or slice thin, wooden boards.
How big of a tree can a 16 inch chainsaw cut?
In general, most professionals recommend sizing up by two inches when choosing a bar length. This means when considering how big of a tree can a 16 chainsaw cut, you can cut a trunk with a width of up to 14 inches.
Is a MS 260 a pro saw?
Yes an 026, ms260 or ms261 are all pro model saws. Same with other sizes of pro model Stihl.
What is the toughest chainsaw?
The new STIHL MS 881 is the world’s most powerful chainsaw in production today. Following on from the highly regarded MS 880 chainsaw, which was a favourite of foresters, the arboriculture industry and saw-mill operatives, the MS 881 was designed with the largest timber jobs in mind.
What chainsaw do loggers use?
Stihl is the most popular chainsaw for professional loggers. It has a long-lasting chain, and you can also enjoy the exceptional cutting speeds available with this brand of chainsaw. Additionally, the chains are high-performance, low vibration, and quiet in their performance.
What is the most aggressive chainsaw chain?
404 chains are the most aggressive. The 3/8 is a more flexible size with adequate strength, low weight and substantial cutting speed. It can also can handle the power of a 50-100cc chainsaw engine.
What chainsaw chain stays sharp the longest?
Husqvarna Chainsaw Chain 16″ . The x-Cut line of Husqvarna chains is also designed to stay sharp longer, so you can cut for a longer amount of time before the chain needs sharpening.
What type of chainsaw chain cuts the fastest?
A full chisel chain is a chain with square cornered teeth, and they’re known for being the fastest cutting blade shape available. A full chisel chain also has a higher number of teeth than other chain options(full chisel is also known as a standard chisel chain).