If you have a new saw, this won’t apply to you, as new regulations require saws to be built so that only a qualified technician can tune the carburetor. If you have an older saw, here’s how to quickly tune it yourself. Less than five minutes of your time can make a big difference in how well your saw runs.
The correct carburetor adjustment will allow the saw to produce maximum power, extend the duty cycle of the engine, produce minimal smoke, idle smoothly, rev up nicely and give trouble free service. High Speed Fuel Adjustment – This is the adjustment that controls the proportion of fuel in the combustible air/fuel mixture at cutting speed. If carburetor adjustment is required due to a new or rebuilt carburetor, it is best to start with the fuel adjustment settings one turn out.
How to Adjust the Carburetor on a Poulan Pro Chainsaw. Adjusting the Homelite chainsaw carburetor involves tuning the idle speed screw. Adjust the screw labeled ‘L’ until the chainsaw accelerates smoothly and sounds smooth.
A carburetor is an exceptional part of a chainsaw that controls the quantity of fuel used by the machine. If you adjust the chainsaw with low fuel, when you fill-up the tank eventually, the carburetor may become too adjusted. Because the carburetor is a key piece to the chainsaw, it is a good idea to know how to adjust it.
It would not be accurate to say this is the most important setting, because all of these adjustments need to be accurate for a saw to perform its best, but this is the adjustment that determines how the saw runs in the cut. If you adjust your saw with a dirty air filter, the saw will run too lean when the filter is cleaned. If proper adjustment for your saw is outside the limited range, take your saw into a shop.
how adjust chainsaw carburetor Related Question:
Why does my chainsaw stall when I give it gas?
Carburetor Adjustment An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. If the saw stalls while it’s idling, adjusting the idle screw, which usually is marked LA, should help.
What are the L and H screws on chainsaw?
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs.
Why does my chainsaw start and then stop?
A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
What is the H and L on a carburetor?
They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet).
Why does my chainsaw only runs on choke?
When your chainsaw only runs if the choke is on the problem, in most cases, is a result of fuel supply problems or a faulty carburetor. To fix the problem you should check and clean the fuel system and carburator.
How do you fix a chainsaw that won’t stay running?
Clogged Air Filter – Check the air filter Your chainsaw’s engine needs the right supply of air to run properly. A clogged air filter can be the reason why your chainsaw won’t start or stay running. Find your chainsaw’s air filter and remove it. If it’s clogged or too dirty, wash it or replace it.
Why does my Stihl chainsaw bog down when I give it gas?
The Job of the Carburetor One controls the fuel mixture when the engine is idling, one controls it when the engine is operating at low speed and one is for high-speed fuel control. When the saw bogs down during cutting, it’s usually the high-speed screw you need to adjust.
Why does my chainsaw keep bogging down?
Many chainsaw operators first notice a problem with chainsaws bogging down when they’re using the chainsaw under load, and this is usually the result of poor air circulation. This issue is caused by a clogged air filter on the chainsaw. Remove the air filter from the chainsaw.
Why does my Poulan chainsaw dies when I give it gas?
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
Why is my chainsaw not getting gas?
If your chain saw isn’t getting gas, the trouble most likely lies in one of those three core components: the fuel tank, the spark plug or the carburetor, or one of the minor parts adjacent to the three.
How do you start a stubborn chainsaw?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
What happens when you run straight gas in a chainsaw?
If straight gas is used, it can damage and ruin the piston and crankcase within a minute, as the gas doesn’t take long to burn out these sensitive parts. Drain the tank immediately into a separate fuel container.
What are the two adjustment screws on a carburetor?
There should be two screws on the front of the carburetor, which are used to adjust the air and fuel mixture. Often these look like flat-head screws and you can use a screwdriver to turn them, adjusting the amount of fuel and air mixing in the carb.
How do you tell if a carburetor is rich or lean?
Q: How Do You Tell if a Carburetor Is Rich or Lean? A: One way to tell for sure is by “reading” the spark plugs. If the plug tip is white, the mixture is lean. If it’s brown or black, it’s rich.
What do the H and L screws do on a carburetor?
This adjustment controls the fuel flow to the low speed or idle circuit. If the carburetor is too far out of adjustment to run, or has been disassembled, start with turning the L and H all the way in and then open 2 turns on each needle.