I’ve seen references to Sighting Marks on a chainsaw for use in aligning the saw cut for felling, but I don’t know what marks these are on my saws. The saw pictures below Billy Bob’s name shows the saw felling lines/sighting marks. If you look at my picture to the left, you will see that I have a 24 inch bar on the saw.
LMAO… obviously you haven’t been fallin’ much timer in your life have ya…. When you “Gun your lay” you use your gunnin’ sights on the saw… back in the days before saws had that line… we would just use the full wrap handle as a “Sight”. The gunning marks are primarily for the gunning cut. Always have made use of saw sighting marks or handle wrap depending on brand – even on small stuff, out of habit.
what are chainsaw felling marks Related Question:
What are the black lines on a Stihl chainsaw?
The black line right above the id tag on the saw, running through the decompression valve, is the felling sight. It runs all the way around the saw except for the bottom.
Which way will a tree fall when cut?
The notch is what will allow the tree to fall properly, so you want it on the “fall side” so the tree will fall in the direction of the notch. The fall side should be the heaviest side of the tree. Cut at a comfortable working height.
Why do loggers run upside down bars?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
What is a red lever STIHL chainsaw?
The red lever just denotes an earlier saw. Like mason said, the really early models (like 034 and 024) had black levers and went to red at some point. Then back to black. It only means that they used red instead of black plastic to make the lever.
What side of the tree do you make the first cut?
With the tree on your left and your left shoulder against the tree, make a 70-degree cut on the side facing the direction you want the tree to fall. If your chainsaw has a felling sight on the housing, use it as a guide.
What is meant by felling of trees?
Essentially, tree felling is the action of cutting down a tree to prevent the spread of disease and improve safety in the area.
How do you cut a Humbolt?
With a Humboldt notch, it’s best to make the top cut first. Using full throttle and entering horizontally, cut inwards to approximately 25% of the diameter of the tree. Next, create your Humboldt cut by cutting upwards at a 45-degree angle until you meet the uppercut.
What is a boring back cut?
On trees leaning backwards or in other undesirable directions, a bore cut allows you to use wedges to control the direction of its fall. When you make a bore cut, a strap of wood at the back of the tree holds it safely and securely, allowing you all the time you need to make the hinge exactly the way you want it.
Why is there a hole in a chainsaw bar?
The hole is part of the manufacturing process when the bar is made at the factory. The milling and heat tempering machines anchor to it and the tail slot. Making a living with a saw since age 16.
What is the hole in the end of a chainsaw bar for?
These two holes are used to hold the saw blade. if your chainsaw blade not have holes or just have one hole. it not work. if you know how to drill, you can drill two holes on your chainsaw blade.
What is full chisel chain?
A full chisel chain is designed for the fast cutting action. In comparison to the semi-chisel chain, this chain has square-cornered teeth which makes it more aggressive when cutting.
What chainsaw chain cuts the fastest?
A full chisel chain is a chain with square cornered teeth, and they’re known for being the fastest cutting blade shape available. A full chisel chain also has a higher number of teeth than other chain options(full chisel is also known as a standard chisel chain).
What is the lightest most powerful chainsaw?
Weighing only 5.7 pounds (without bar and chain), ECHO’s CS-2511P is the lightest gas-powered rear-handle chainsaw in the world with the most power in its class, states the company.
What CC is a Stihl 066?
Engine Specifications The 066 uses a single cylinder two-stroke engine with a displacement of 91.6 cubic centimeters.
When was the Stihl 066 made?
1998 was the first year of the round top 066 which carried into 2002 with the MS660.