Exposure to moisture could cause a chainsaw to rust, and this could make it hard to start the chainsaw. If you store your chainsaw in a place that isn’t good for it, then you’ll be more likely to have the chainsaw rust over time and parts of the chainsaw might get gummed up. Yes, sometimes chainsaws can get hard to pull due to getting older, and it might not always be the best decision to make to keep trying to fix the chainsaw.
When the threat of a dislocated shoulder becomes a real possibility as you reach for the starter cord on the chainsaw the signs are there that it’s time to check a few things on the saw. If it is easy to pull the starter cord and there is no fuel spurting out through the spark plug opening, then you are on the right track. As we have checked the bearing, cylinder, and piston, and the exhaust is clear it’s time to turn our attention to the starter cord and starter system itself.
Damaged rope can cause other parts of the starter assembly to damage; hence; it is very pertinent to replace the rope immediately. You can prevent the new starter rope from fraying by burning the two ends of the rope. 5. Fix the rope such that the pulley rotates a little more than half turn whenever the rope undergoes maximum extension.
It is so hard to pull, I cannot pull it fast so when it hits, it snaps my fist back into the machine. Yes your buddy was right about the old Stihls I have a 1976 031 AV and a 041 they just keep trucken if you can find parts, if you find parts saws cheap squirrel them away. I learned a lot including how to live with a saw that is very hard to pull.
what makes a chainsaw hard to pull Related Question:
What causes a chainsaw to have too much compression?
Many problems with compression are related to fuel. Old or bad fuel can cause lots of headaches with yard equipment. Try draining any of the gasoline mixture left in the gas tank and add fresh fuel. If this does not solve the problem, it may be related to excessive fuel caused by problems in the gas lines and filters.
Why is my chainsaw weak?
A weak spark on a Husqvarna chainsaw can be caused by one of these misfiring components in the ignition system. Properly maintaining and cleaning the saw on a regular basis will prevent most spark issues. Most problems can be isolated easily and fixed with a few simple tools and parts.
What causes a chainsaw to vapor lock?
Vapor lock occurs when the fuel (usually gasoline) within the fuel delivery system overheats and vaporizes too rapidly. The resulting excess gas bubbles accumulate to the point of actually blocking normal fuel delivery.
Why is my chainsaw hard to pull and kicks back?
If your chainsaw is hard to pull, here are some common causes: The pully system is snagged or stuck. The starter assembly is stuck or sticky. The housing may be damaged.
Why does my chainsaw get dull so fast?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
Can I use wd40 on my chainsaw?
We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.
How do you start a stubborn chainsaw?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
Why is it hard to start my Stihl chainsaw?
Problems starting a Stihl chain saw can be related to gasoline storage, spark plugs, and incorrect starting procedures.
Why does my chainsaw bog down when I give it gas?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
How do you stop vapor lock?
Once the fuel system has cooled, you can help eliminate any vapor left in the fuel system by first pressing the accelerator pedal slightly (do not press it to the floor) while cranking the engine. Once the engine starts, hold the accelerator pedal down until the vehicle runs smoothly, indicating the vapor lock is gone.
Why does my chainsaw stall when I give it gas?
Carburetor Adjustment An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. If the saw stalls while it’s idling, adjusting the idle screw, which usually is marked LA, should help.
How long does it take to Unflood a chainsaw?
The first option is the easiest since it doesn’t require any effort on your part, it just takes time. Many people wonder if a flooded chainsaw will fix itself? The answer is yes, but not always. By letting the chainsaw sit for about 20 minutes it will allow some of the fuel inside the engine to evaporate.
How much compression should a chain saw have?
According to Stihl USA, the minimum compression reading for their chainsaws should be around 110 psi. Some individual engines may run a bit higher or lower and the temperature of the tool can affect readings.
Can you check compression by hand?
Can I Do A Compression Test By Hand? It is possible to test this yourself with a compression tester, a few hand tools, and 20 minutes. The first step is to remove the fuel pump and fuel injection fuse. Using a spark plug hole, start the threaded end of the compression gauge.
Does hard wood dull a chainsaw?
Re: Chainsaw and oak Very hard but really puts out the heat in the fireplace. If you cut it green it is not too bad. After it has dried it will dull a chain about each tank of gas. And that was Stihl chain.