This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil or an inferior type of oil that is being slung off the chain and not lubricating. A properly sharpened chain will require little pressure be applied to have it cut correctly.
If your chainsaw is smoking from the engine, then your problem is more serious, and has potential to do greater damage to the machine. Alright, now that we’ve covered the 2 groups of things that DO cause chainsaw smoke, I also wanted to mention some things that DO NOT cause chainsaw smoke. The 2 things to look at, when troubleshooting a smoking chainsaw.
Chainsaw that smokes a lot: frequent breakdowns Smoke from a bad oil-gasoline mixture The main reason for a chainsaw that emits smoke, is the result of a bad oil / fuel mixture or bad oil. If your chainsaw smokes, it is likely that it is due to a segment problem. Smoking chainsaw: rare breakdowns A smoking chainsaw chain.
what causes my chainsaw to smoke Related Question:
What causes white smoke from a chainsaw?
Smoke from a bad oil-gasoline mixture The main reason for a chainsaw that emits smoke (white most of the time), is the result of a bad oil / fuel mixture or bad oil. The oil / fuel mixture is to be prepared carefully, taking into account specific percentages.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
What causes a chainsaw to overheat?
Common reasons behind chainsaw overheating are a wrong oil/fuel mixture, a blocked or clogged exhaust. It is also possible that the air filter is clogged. Or you are using a dull chain. If you are using your chainsaw for an extended time, or it is not powerful enough for the job, it can also overheat.
Why is my chainsaw smoking and not cutting?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
How do you stop a chainsaw from overheating?
To prevent chainsaws from overheating they must be cleaned regularly. The cylinder and starter both contain air intake areas that pull cool outside air into the engine when it’s running. If dust, wood chips or other material blocks these systems, the engine will start to overheat.
When should you throw away a chainsaw chain?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
Is it worth sharpening a chainsaw?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How often should you replace your chainsaw chain?
The chain sprocket must be replaced if the depth of the wear marks reaches about 0.5mm, i.e. the wear limit. A seriously worn chain sprocket can cause the chainsaw chain and guide bar to wear at an increased rate, as well as reducing cutting performance too, so it’s important to keep an eye on.
Why does my chainsaw chain dull so quickly?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
Can you run a Stihl chainsaw without an air filter?
Don’t Run Your Chain Saw With a Dirty Air Filter But if you don’t clean/replace your air filter (shown here), the engine will suck some of that dirt and dust into the combustion chamber, causing excessive wear.
Can you clean a Husqvarna chainsaw air filter?
Step-By-Step Chainsaw Air Filter Cleaning Process Remove cylinder cover. Remove the air filter. Give the air filter a once over, looking for any external dirt build-up, damage or wear. If there is a lot of dirt, wash the filter with a soft brush in warm soapy water and rinse until the water runs clear.
How long should a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.