It’s best to use a different chain to a skip tooth chain when sawing material that is narrow or has a small diameter. A regular ripping chain is not the same as a skip tooth chain. A ripping chain can be combined with a skip tooth chain style.
The chain in the second photo is a skip chain with a cutting tooth on every third link. A skip chain has fewer cutting teeth than a conventional chain which means it won’t be dragging as many teeth through the wood you’re cutting. The debate for and against skip chains sometimes rages among professionals and, while the professional saws have adequate power for even the largest logs, one logger I talked to summed it up this way saying, “They just seem to work better with skip chains.”
Long cuts, common in these conditions, require the chain to carry chips a long distance before they are expelled. It will always be the fastest and smoothest cutting sequence on short cutting attachments. On the other hand, if most cuts on the job require burying the bar in a deep cut, a skip sequence would probably be the best choice.
“A while back I ordered chain over the phone. I told him to send me a ripping chain and a crosscutting chain for the 36″bar I was getting. “On my bigger saws I try to avoid using skip chain on anything fairly loose and smaller then 3”, limbs and such, the chain will just suck it up into the saw jamming it or throw it back or draw the saw forward. “Wood at the time was fresh spruce.I was trying to come up with a fast chain for bigger wood. Full comp should be faster, but I couldn’t get this NEW full comp loop faster then the half used up skip chain. I figure it had to be because the half used skip was cutting better do to the cutter location being further back and maybe something to do with pulling of chips slowing the full comp chain up. Just guessing on that too.The full comp loop was getting close then I hit a 4” knot in the last cut with the raker’s taken down to throw the timing out the door.
To elaborate a bit more on Freakingstang’s post: Full skip Left cutter, tie strap, tie strap, right cutter, tie strap, tie strap, left cutter, etc. Of course, the bigger bars also have full skip, 32″ and up. You should be able to get semi-chisel in semi or full skip if you want.
what is a chainsaw skip chain Related Question:
What is a full skip chain?
STIHL RAPID™ Super Full Skip is the skip pattern version of STIHL RAPID™ Super. There are two tie straps between every two cutting teeth, allowing better chip discharge and higher chain speed.
Is a skip tooth chain the same as a ripping chain?
Ripping chain is ground at a less aggressive angle which allows for a smoother surface finish on the slabs you cut, therefore you should probably be using ripping chain. A skip chain has less teeth on it than a chipper chain of the same size.
What are the different types of chains for a chainsaw?
Chainsaw chains come in three main varieties. They come in full chisel, semi chisel and low profile chains, with each being used for different tasks. The chisel refers to how the teeth are cast on the chain itself – which then determines how the chain cuts through the wood.
What is the fastest cutting chain for a chainsaw?
A full chisel chain is a chain with square cornered teeth, and they’re known for being the fastest cutting blade shape available.
When should you use a full skip chain?
Full-Skip is our best selling sequence. It is usually preferred by customers who run long bars and cut large softwood trees. Long cuts, common in these conditions, require the chain to carry chips a long distance before they are expelled.
Why do Loggers Run chainsaw bars upside down?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
What is the advantage of a skip tooth chain?
A skip chain has fewer cutting teeth than a conventional chain which means it won’t be dragging as many teeth through the wood you’re cutting. Less drag on the chain means less power is needed to cut through the log. That means the motor on your saw runs faster which keeps it in a more efficient power curve.
How do I know what chain to buy for my chainsaw?
To determine the pitch (chain size), you’ll need to measure the distance between any three consecutive rivets, then divide the result by 2. The rivets are the small, round pegs/studs that hold the chain segments together. Measure from the first to the third, then divide that number in half to get your chain pitch.
What is the most aggressive chainsaw blade?
404 chains are the most aggressive. The 3/8 is a more flexible size with adequate strength, low weight and substantial cutting speed. It can also can handle the power of a 50-100cc chainsaw engine.
What does full chisel mean on a chainsaw chain?
A full chisel chain is designed for the fast cutting action. In comparison to the semi-chisel chain, this chain has square-cornered teeth which makes it more aggressive when cutting.
Can a chainsaw run without a muffler?
A chainsaw will run perfectly without a muffler but using it without the muffler is not recommended for two main reasons. Firstly, the muffler reduces the noise made by the saw, and secondly, it provides protection to the cylinder by keeping debris from getting in.
Why is there a hole in a chainsaw bar?
The hole is part of the manufacturing process when the bar is made at the factory. The milling and heat tempering machines anchor to it and the tail slot. Making a living with a saw since age 16.
How long does a chainsaw chain stay sharp?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
What does MS mean on Stihl chainsaws?
Every STIHL chainsaw model name starts with MS, MSA, or MSE. The common part, MS, stands for Motorsäge which is German for chainsaw. MSA indicates that it’s a battery chainsaw and MSE tells us that it’s an electric model.
Does a ripping chain cut faster?
Ripping chains are slower as the finer cut and surface takes more time than regular cutting.