If this item is ordered alongside one of our machines, select the option for free shipping to combine the delivery charges. Delivery on this item to UK addresses is the standard rate of £5.00. If this item is ordered alongside one of our machines, select the option for free shipping to combine these charges.
what oil for titan chainsaw Related Question:
Can I use any oil for chain saw?
First, check your manufacturer’s instructions before adding alternative bar oil to your chainsaw. Generally, chainsaws can handle a wide range of lubricants. Vegetable and canola oils work well, and automobile motor oil will too, as long as you observe the SAE ratings and use the appropriate oil weight for the season.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
What viscosity is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
What happens if you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
Can I use 2 stroke oil for chainsaw?
Modern two stroke chainsaws do not require generic brand oils to operate at temperatures and rpms that are comparable to those of generic brand oils. Our recommendation is to use only high quality two stroke oil designed for air cooled high performance engines when using your modern two-cycle engine.
Can you use transmission fluid for chainsaw bar oil?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .
Can you use 10w40 in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30. Thicker.
What is bar oil equivalent to?
Canola oil It is thinner than regular vegetable oil, meaning it will tend to fly off the chainsaw more quickly – but it has a more suitable viscosity at lower temperatures so makes a good substitute for chainsaw oil when it is too cold to use vegetable oil.
How often should I oil my chainsaw?
It is recommended that you grease the bearing in the tip of the bar each time you refuel. Make sure to grease the tip at the end of the day as well to help prevent moisture from entering the bearing as the bar cools.
Can I use WD40 as chainsaw oil?
No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant. WD40 is primarily a solvent or rust dissolver.
Why does my chainsaw blade go dull so fast?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
Can I use 5w30 for bar oil?
You’ll be fine.
Can I use regular oil instead of bar and chain oil?
While motor oil is not the best substitute for chainsaw bar oil, it will work as a temporary measure if find you have no other option. The downside of motor oil is that it’s not sticky enough to stay on the bar and chain. So, when you’re using the chainsaw, the motor oil will fling off as you cut and make quite a mess.
Can you lube transmission oil as chain?
Yes definitely you can use. I have been using gear oil of 140 grade on my dominar400 since past 9months. But before lubricating the chain make sure you clean the chain with diesel and wipe it with a cloth then apply the gear oil. I found gear oil to be better than chain spray.