Whether your tool needs sharpening or an entire chainsaw brake repair, maintaining and servicing it is integral to prolonging its service life. Once they locate the cause of the issue, your Tasker informs you of the repairs required to fix your chainsaw. If your chainsaw is deemed unrepairable, then it may be best to replace it instead. It’s a whole lot safer as you can avoid further damages and accidents from occurring due to faulty components.
We have a staff of technicians who are factory trained and certified, as well as OPE certified, with over 100 years combined experience in outdoor power equipment service and repair. We require a deposit and pre-authorization at the time equipment is dropped off at our shop. If you decide not to repair your unit, the deposit covers the cost of teardown and diagnostic service already performed, but doesn’t cover re-assembly of the unit.
where to get my chainsaw serviced Related Question:
How much does it cost to service a chainsaw?
THE AVERAGE CHAINSAW SERVICE IS $100 TO $125 If we can find ways to help save you money, we will suggest them to you. If we do not feel it is worth repairing, we will tell you so.
Do chainsaws need to be serviced?
Chainsaw’s provide many years of service for very little upkeep. Taking the time to service your chainsaw will help ensure that your equipment will not let you down. For safety reasons, make sure you only service your chainsaw when it is fully cooled, with the spark plug disconnected.
How much does it cost to service a Stihl chainsaw?
Service Description. General service is $49.50 labor plus parts (Air filter, fuel filter, spark plug, chain etc)
How often should you service a chainsaw?
Obviously this depends to some degree on how often and how heavily you use your chainsaw but experts generally recommend you get a professional service or check-up from every few months for heavier use to at least once a year for light use.
How often should you change the spark plug in a chainsaw?
A poorly functioning engine in a Stihl chainsaw can mean more work for the operator and can even be dangerous. Consequently, Stihl recommends replacing the spark plug after every 100 service hours.
What can I do with an old chainsaw?
Gas and oil can be disposed of at a household hazardous waste collection site for free. Remove non-metal parts and place in the trash. Metal parts can be recycled as scrap metal.
How do you store and clean a chainsaw?
In a well-ventilated area, take a bucket and mix one cup of ammonia with one gallon of water. Place the chainsaw chain in this solution and let it soak for 15 minutes. Put on a pair of thick rubber gloves for protection. Then, use a soft-bristled toothbrush to scrub each section of the chain until it’s free of debris.
Why does my chainsaw chain dull so quickly?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How do you know if a spark plug is bad in a chainsaw?
If it’s not producing any sparks at all, your chainsaw needs a new plug. If there are only a few sparks coming out of one side of the electrodes but none on the other side, it’s not bad enough for you to worry about, but it will affect your performance.
What does H and L mean on a chainsaw?
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs.
Can you clean a spark plug with wd40?
WD-40 removes carbon residue and keeps moisture away from spark plugs and spark plug wires. WD stands for Water Displacement, so if your spark plugs are wet or you need to drive moisture away from ignition distributors, for example, WD-40 is a product you should have handy!
How do you drain old gas from a chainsaw?
Move to a well-ventilated area and unscrew the lid of the gas tank on the chainsaw. Situate your plastic gas can within reach and remove its lid as well. Place the straight portion of your hand siphon into the chainsaw’s gas tank. Insert the drainage hose of the siphon into the gas can.
When should you throw away a chainsaw chain?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
Can a chainsaw cut through dirt?
Don’t Cut Into Dirt All it takes is a second in the dirt to dull the cutters. In addition to dulling the cutters, dirt also wears out the chain links faster, causing the chain to stretch. Plus, dirt wears the sprocket at the bar tip.