Check and replace bar and chain oil regularly to reduce friction, keep the saw from wearing out faster, and to make cutting easier. Be sure to use bar and chain oil, Not regular motor oil. Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
Knowing the available chainsaw oil options, learning how to choose the right one and determining the right fuel/oil ratio can help ensure your chainsaw runs smoothly every time. Common Issues if Chainsaw Oil Is Bad. Chainsaw engine oil can go bad. Two-cycle oil is good for up to five years when sealed, and many manufacturers list the oil’s shelf life on the container. “One thing we do for our customers who buy a chainsaw that requires an oil/gas mix is we have them buy a gas can and we write the formula right on the can with a big black Sharpie. Then, the next time they need to make the mixture, they can dump in the right amount of oil and take the can to the gas station and pump in the right amount of gas.”
This is different than the oil that you mix with your gas to provide lubrication to the engine, and I’m going to describe below the importance of this task and explain how to oil your chainsaw for both the safety and care of your saw. Most saws come with a sample bottle of oil and suggestions of which oil to by- but for the most part, the oil is that same from one brand to the next. Saws are designed to feed oil as it runs, so most tanks are large enough to hold enough oil for a full tank of gas.
At Gardening Products Review, we highly recommend oil manufactured for this specific use. Chainsaw shown in this video tutorial is the Redback 40V 12″ Li-Ion Cordless Chainsaw. The bar & chain oil featured in this video is Husqvarna Bar & Chain Oil – 1 Gallon.
where do you put chainsaw oil Related Question:
Do I need to put oil in chainsaw?
Why use oil? You want lubrication of the actual chain against the bar. You don’t want to chain to burn – which is what might happen if there’s too much friction. Without oil, it causes frictional force on the motor in the chainsaw as well.
How often should I oil my chainsaw chain?
Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
What happens if you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Can I use WD40 as chainsaw oil?
No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant. WD40 is primarily a solvent or rust dissolver.
What is special about chainsaw oil?
Chainsaw bar oil has a certain level of “slickness” to it. This slickness keeps the chain spinning at a fast rate without getting slowed down by the friction that occurs when metal rubs against metal. So, if you want to use the “correct” type of bar oil in your chainsaw, consult the manual and use what it suggests.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Do electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
Can you use regular oil for chainsaw bar?
Whether you use bar and chain oil, traditional motor oil or a vegetable oil-based lubricant, always make sure you’re using fresh oil when you fill your chain saw’s bar oil reservoir. Never use waste oil that you drained from your car or boat.
Can I use 2 stroke oil for chainsaw bar oil?
Can You Use 2 Cycle Oil As Bar Oil? You should only use two-cycle oil as the mix, never as a chainsaw bar oil alternative. Using two-cycle oil on the bar will not provide enough tackiness to stick to the chainsaw chain in the summer months. Two-cycle oil also will not work in the winter.
How often do you need to sharpen a chainsaw?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
Can you start chainsaw without bar?
It is not recommended to run a chainsaw without a chain. If you need to run it as a movie prop or you are fixing the engine, ensure that you run it for a short time only. I do not recommend letting it run for more than 5 minutes. Without a chain, the chainsaw will cause the engine to rev higher.
What weight is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
Can I use chainsaw oil in my lawn mower?
Got a two-stroke engine? Any two-stroke motor oil made for air-cooled engines, such those in chainsaws, water pumps and weed eaters, will work perfectly in your two-stroke lawn mower engine.
What does 10W30 mean?
The 10W30 designation on engine oil means that the viscosity of the oil is rated at 10W when an engine is cold and 30 when the engine is hot. This is different than an oil labelled 5W30, which has a thinner viscosity when the engine is cold at 5W.