Sometimes you’ll find your chainsaw chain grabbing after using it for a while as it has a set of teeth attached to it’s rotating chain which catches the wood as it runs along the guide bar. There are a number of signs you need to pay attention to on your chainsaw to know if there’s a chance of your chainsaw chain grabbing when cutting logs. As much as possible, try keeping your chain out of the dirt when cutting, to reduce the chances of your chainsaw chain grabbing soon afterwards.
It has full skip chain on it and this may be the problem but the chain is really grabby. It sometimes will stall the chain and you have a hard time getting the chain out of the cut it is so deep in the wood. The guy at the saw shop talked me into full skip and I’m thinking I should have went for semi skip, or it may just be a bad chain.
I’m having a problem with my chainsaw “Chattering” or grabbing and bouncing around when I try to bore cut with it. Friend of mine has the habit of trying to go slowly into the bore cut by running at part throttle. Now when I bore with the saw in an upright position, like when I’m bucking, I often bore the conventional way using the bottom of the nose.
It should not take a huge amount of effort or force to start a cut with a chain saw since it should “Bite” right into the wood. Dull teeth on the chain keep the saw from biting the wood. Using the chain saw when the teeth are dull can damage both the chain and the saw.
chainsaw grabs when cutting Related Question:
What causes a chainsaw to grab?
Teeth are totally broken or worn out unevenly. Regular issues with chain Tension. Presence of smoke when cutting. An unbalanced feel when using the chainsaw or it cuts unevenly during use.
How do I stop my chainsaw from pinching?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
Why does my chainsaw bounce when cutting?
Chainsaw chain jumps and is broken The chain saw belt jumps when it breaks at full speed. This situation can be caused by using an unsuitable chain. This happens when you are cutting very hard wood with a gouge chain. It is indeed very important to choose the right belt for the job to be done.
Why does my chainsaw keep jamming?
Here are our explanations! Indeed, whether it is a chainsaw electric ou thermal, it is the teeth of its links that come into direct contact with the wood and the materials to be cut. As a result, dirt, wear on the guide or links and even the motor can be the cause of jamming.
When should you throw away a chainsaw chain?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
What should you not do with a chainsaw?
Don’t Cut With Improper Blade Tension A overly loose or tight chain also wears out the drive sprocket and causes rapid chain and bar wear. To determine if your chain is properly tensioned, pull up on the chain. The drive links should still be in the bar groove. If the links come out of the bar, the chain is too loose.
Can you fix a pinched chainsaw bar?
To open pinched rails, mount the bar in a vice and gently tap on the bent rail with a hammer and punch. A flat-blade screwdriver is another tool that can be useful for prying open bent bar rails. Once you’ve got the pinch worked out, test your repair by placing the chain back in the groove.
What happens if you file rakers too low?
If you take your rakers down too low, on the other hand, your chain gets very aggressive and either stalls out in the cut or (worst case scenario), hangs up in the cut and kicks back at you.
What does a chainsaw Raker do?
Chainsaw rakers control how deep the chainsaw tooth cutter penetrates the wood. Essentially what they do is prevent the edge of the tooth from biting too much into the wood. Rakers help determine the height that the teeth cutters will cut into the wood.
Should a chainsaw chain move freely?
The chainsaw chain should feel snug but still pull freely. Finally, perform a “snap” test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How do you know if your chainsaw sprocket is worn out?
The chain sprocket must be replaced if the depth of the wear marks reaches about 0.5mm, i.e. the wear limit. A seriously worn chain sprocket can cause the chainsaw chain and guide bar to wear at an increased rate, as well as reducing cutting performance too, so it’s important to keep an eye on.
Do I cut compression or tension first?
Always cut on the compression side first! The area on the outside of the bend will pull apart when cut. This is the tension side. If you decide to cut this side only, the tree will split apart before the cut can be completed.
What is chainsaw bucking?
The process of cutting a tree into usable lengths is called bucking. Bucking often occurs as a tree is being limbed, such as when the limbs of the crown are to be used as firewood.
What should you not do when a tree falls off?
When cutting up a felled tree, avoid touching the ground with the chain because even a brief encounter will severely dull the cutting teeth on your chain saw. If possible, cut partially through the tree and then rotate it to cut the rest of the way through.