I like to let my chains soak in Bar Oil plastic tub with a lid on it, for over night, and let them hang for over another night, to let the some of the excess Bar Oil drip off them into another plastic tub, so I don’t get Bar Oil, all over the floor. I then install the New Chain onto the Chain Saw, and take the saw outside. I run the Chain Saw like this, for about 5 to 10 minutes.
The purpose of the added oil is to ensure proper lubrication of the new engine during break-in. The main purpose of chainsaw break-in is to improve the seating of the engine’s piston rings on the cylinder wall. Breaking a chainsaw in is a part of good operation protocol but not absolutely needed: with modern saws, no adverse effects are likely to follow from an omitted break-in period.
If you just purchased a new Stihl chainsaw, it’s a good idea to break it in before using it for any cutting projects. Immediately using it to cut anything, particularly very heavy or dense wood, can ruin the chain. Although Stihl chains are pre-stretched, running a new chainsaw through a short break-in period helps smooth any small imperfections and allows the chain to settle into the rivets properly, according to Stihl’s publication “Sharp Advice for Chainsaw Owners.”
how to break in a chainsaw chain Related Question:
Do I need to break in a chainsaw?
Typically we recommend a break in period of 6-10 tanks of fuel. During this period the engine should not be allowed to run at high RPMs for extended periods of time.
Is there a break in period for new chainsaw?
When using a new Stihl chainsaw, it is important to adhere to the break-in period, which lasts for the first three tanks of gas.
How do you break in a new bar and chain?
A chain should be tensioned correctly and run without load at partial throttle for about 3 minutes to break it in. Ample lubrication is essential during this period. If the saw is equipped with an adjustable bar and chain oiler, the maximum flow should be set for the first hour of operation.
How do you break in a new piston on a chainsaw?
in chainsaws that recommend 8 oz to 1 ga. On a fresh rebuild, I use 40-1 and add about 1/2 teaspoon of extra oil to full tank. I use the saw, with extra oil, but avoid high rpm out of cut and extended idling, until two or three tanks have been used. After that, I use regular mix,40-1 and do final carb setting.
Should you run a chainsaw at full throttle?
Engine Protection Generally, two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown. Therefore, running at any throttle speed below the full throttle is not advised.
Should you warm up a chainsaw?
The gas engine in a gas chainsaw should warm up, but due to the engine’s small size, this will happen quickly. Normally the engine will run for a short time after startup before you really start using it, giving the oil enough time to warm up and lubricate all engine parts.
How long should you run a chainsaw?
Depending on the type and usage, you can expect a gas Chainsaw to run between 15 and 40 min before you have to fill it up again. Most battery-powered chainsaws have a run time of up to 2 hours, but there are high-capacity power packs that will last much longer.
How long do Husqvarna chainsaws last?
It ultimately comes down to the factors listed above (especially maintenance). That being said, you can expect a quality chainsaw to last you at least 10 years or more. But if you take care of it, I know people who have saws that have lasted 20-30 years and even longer.
Why does my chainsaw chain keep breaking?
Chainsaw chains come off the bar due to worn-out bars, worn-out sprockets, and wrongly set tension. You should also note that with continued use, chains lose their tension and hence are more likely to come off the bar when you least expect it.
Do Stihl chains have a down angle?
STIHL saw chains are generally filed to an angle of 30° – parallel to the service mark for the filing angle. Hold the file so that one quarter of its diameter projects above the top plate.
What should you not do with a chainsaw?
Don’t Cut With Improper Blade Tension A overly loose or tight chain also wears out the drive sprocket and causes rapid chain and bar wear. To determine if your chain is properly tensioned, pull up on the chain. The drive links should still be in the bar groove. If the links come out of the bar, the chain is too loose.
Can you cut with the top of a chainsaw?
While it’s designed to cut with either the top or bottom of the blade, just about anything that comes in contact with the top half of the end tip of the blade (known as the kickback zone) can change the cutting momentum and cause the saw to slam back against you.
Can a chainsaw be used in the rain?
Yes, you can. The pouring rain will not damage your chainsaw, and you can perfectly continue working on your project. Just make sure the engine is not submerged in water. So, if you were thinking about postponing your woodcutting plans due to rain or snow, now you know there is no harm.
How do most chainsaw accidents happen?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
When should you throw away a chainsaw chain?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.