Dull cutters damaged by rocks can cause a chain to cut crooked. It’s important to remove all damage from cutters prior to cutting. Cutting with a dull chain can accelerate wear to the bar and chain.
When the saw teeth become chipped, damaged or dull, the chainsaw likely won’t cut straight, especially if more teeth are affected along one side of the chain. Sharpen the teeth uniformly using a file and file guide, or take it to professional for sharpening. Madsen’s recommends using a grinder rather than a file, if you want to avoid taking it to a professional.
The most probable reason why a chainsaw pulls either to the right or left during a cut is because it was sharpened unevenly. Keep working the side which you feel lacks attention, and eventually the chainsaw should start going as straight as new. The teeth have to be equally sharp on each end to make the chainsaw work straight.
why does a chainsaw cut to one side Related Question:
How do I stop my chainsaw from cutting crooked?
Check the size of the top plates, which sit on the longer sections of each tooth on the chain. These top plates should be the same size. If some are shorter than others, file the longer ones down to match. Keep the same angle on all the top plates as you file – angles that don’t match also can cause curved cutting.
Why does my chainsaw cut sideways?
Uneven top plates can cause a chain to cut crooked. It’s important to keep all top plates equal length. Dull cutters damaged by rocks can cause a chain to cut crooked. It’s important to remove all damage from cutters prior to cutting.
Can a bent chainsaw bar be straightened?
Solid body bars with replaceable noses can be straightened by hammering with the bend peak up on a flat anvil. Laminated bars need a piece of rubberized belting of approximate 1/4″ thickness between bar and anvil to properly hammer straighten .
Why does my chainsaw smoke when cutting?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
Why is my chainsaw chain not tightening?
If you’re having trouble tightening the chainsaw chain, it may be adjusted properly already. Check the tension on the chain by grasping it in the middle of the top of the guide bar and giving it a quick snap. The chain should quickly snap back into place with no sagging on the underside of the guide bar.
Can you bend back a chainsaw bar?
The bar fits over the chain blade. Sometimes the chainsaw bar bends or breaks while handling heavy jobs. Severely bent chainsaw bars need to be replaced. However, a mildly bent bar can be straightened by following a few simple steps.
Can you straighten a chainsaw blade?
If you just have a few drive links twisted a vice will usually straighten them out . If however you bent the drivers up in the chain it’s self it might not be a bad idea to just change them rather than take a chance of breaking a chain .
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
Can you run a chainsaw without the bar and chain?
You can run a chainsaw without a chain, but I wouldn’t recommend this for more than a few minutes. The engine will rev up higher, and these increases wear and tear. It can also run hot when the throttle is used. Ensure that you empty the bar oil tank, else oil can spray out of the chainsaw.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
Why does my chainsaw blade get dull so fast?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
Why do chainsaw chains stretch?
A chainsaw chain stretches and loosens from tension and extreme friction. The friction from cutting through wood makes the chain very hot and the heat causes it to loosen. The heat expands the guide bar and when it cools, the chain has stretched. The chain will also loosen as it wears down from use.
Does a chain on a chainsaw stretch?
Over time, the chain on your chainsaw will become loose, and new chains will stretch a lot more when you are breaking them in. You need to pay attention so that you can tighten a loose chain before you turn the chainsaw on, as loose chains are dangerous.