Look the chain saw over, and clean any debris or stuck pieces of wood from all areas surrounding the chain. Grab the chain, and ensure that it turns on the chain saw bar. If after freeing up the pull-cord or replacing it, you find it operational, this also means the piston is moving freely inside the chain saw engine.
One of the most common problems that chainsaw users often face is when their chainsaw seizes. A seized chainsaw should be quite the problem for chainsaw users, especially when they are in the middle of an actual job. A chainsaw can seize up when the carburetor was set too lean or whenever it isn’t functioning properly.
If the pistons of your engine are jammed in their cylinders or the crankshaft is bent, it’s a sign of engine seizure and as a result, your chainsaw would be locked up. If no compression is recorded at the gauge, then most probably your engine is seized and you should consider investing in a new chainsaw. The sudden throttling up of your engine can raise the temperatures abruptly which can damage the gaskets and rings of your engine.
Fuel especially pump fuel doesn’t last long, looses it’s volatility and ethonal fuel absorbs moisture. I’ve never had saw issues using fuel a few months old or even 6 months old although I try to keep the fuel less than a month, same saw for thirty years. Hill Top no worries about the oil settling out of mixed fuel.
why did my chainsaw locked up Related Question:
What would cause a chainsaw to lock up?
The reason why a chainsaw seizes is that the lack of lubrication on the piston. When the piston got stuck due to lack of lubrication, it seized the chainsaw engine up. In some cases, the same can happen if the chainsaw’s carburetor is too lean or if it was not functioning properly.
What is a chainsaw brake?
One of the most important chainsaw safety features is the chain brake, which stops movement of the chain in the event of kickback during operation. The chain brake is activated when the front hand guard, located near the saw’s upper handle, moves rapidly toward the chainsaw operator.
How do you know if your chainsaw clutch is bad?
Does the engine loose revs, or the engine keep revving and just the chain stops? If the engine is still running at normal revs, and the chain slows down, then it’s a problem with the clutch. Worn out, gummed up, jammed springs etc. If the engine looses revs under load then it’s more likely a fuel or carb problem.
Where is the choke on a Stihl chainsaw?
The choke position is the fourth setting on the master control lever. This setting is used to start the saw when its motor is cold. Stihl chainsaws denote the choke position using a nearly horizontal squiggle between two vertical lines at the lowest position on the master control lever.
Why is my Stihl chainsaw not starting?
Dirty or clogged fuel tanks, dirty fuel filters and lines, loose fuel hoses, dirty air filters and a dirty carburetor can all restrict fuel flow. Check, clean and replace all the fuel system parts before moving into the internal engine, as gas problems create a majority of starting problems.
What does the C mean on a Stihl chainsaw?
High-performance saws to help make your job easier To help you identify model features, look for these corresponding symbols: C = Comfort feature, E = Easy2Start™, Q = an additional chain braking system, R = wrap handle, and M = STIHL M-Tronic™.
When should you throw away a chainsaw chain?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
How often should you change the bar on a chainsaw?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.
What type of chainsaw chain cuts the fastest?
A full chisel chain is a chain with square cornered teeth, and they’re known for being the fastest cutting blade shape available. A full chisel chain also has a higher number of teeth than other chain options(full chisel is also known as a standard chisel chain).
How much does it cost to fix a chainsaw?
THE AVERAGE CHAINSAW SERVICE IS $100 TO $125 If we can find ways to help save you money, we will suggest them to you. If we do not feel it is worth repairing, we will tell you so.
What happens if you run a chainsaw with the brake on?
Running a chainsaw with the brake on can be dangerous for you and anyone in your vicinity. The chainsaw will not cut, but it still creates sparks that can cause fires or startle nearby pets. It also doesn’t allow the saw to cool down enough which increases the likelihood of overheating and breaking down.