More info about why is my chainsaw so hard to pull

Let’s take a look at some of the most common issues that can come up when your chainsaw is hard to pull and the simple steps you can use to fix it. If the spring or pulley is damaged, the chainsaw cannot start and it will either feel too easy or too hard to pull. Often the chainsaw will start to fail and is hard to pull because it gets old and a part breaks.

Exposure to moisture could cause a chainsaw to rust, and this could make it hard to start the chainsaw. If you store your chainsaw in a place that isn’t good for it, then you’ll be more likely to have the chainsaw rust over time and parts of the chainsaw might get gummed up. Yes, sometimes chainsaws can get hard to pull due to getting older, and it might not always be the best decision to make to keep trying to fix the chainsaw.

When the threat of a dislocated shoulder becomes a real possibility as you reach for the starter cord on the chainsaw the signs are there that it’s time to check a few things on the saw. If it is easy to pull the starter cord and there is no fuel spurting out through the spark plug opening, then you are on the right track. As we have checked the bearing, cylinder, and piston, and the exhaust is clear it’s time to turn our attention to the starter cord and starter system itself.

Damaged rope can cause other parts of the starter assembly to damage; hence; it is very pertinent to replace the rope immediately. You can prevent the new starter rope from fraying by burning the two ends of the rope. 5. Fix the rope such that the pulley rotates a little more than half turn whenever the rope undergoes maximum extension.

It is so hard to pull, I cannot pull it fast so when it hits, it snaps my fist back into the machine. Yes your buddy was right about the old Stihls I have a 1976 031 AV and a 041 they just keep trucken if you can find parts, if you find parts saws cheap squirrel them away. I learned a lot including how to live with a saw that is very hard to pull.

why is my chainsaw so hard to pull Related Question:

What causes a chainsaw to be hard to pull?

If your chainsaw is hard to pull, here are some common causes: The pully system is snagged or stuck. The starter assembly is stuck or sticky. The housing may be damaged.

What causes a chainsaw to have too much compression?

Many problems with compression are related to fuel. Old or bad fuel can cause lots of headaches with yard equipment. Try draining any of the gasoline mixture left in the gas tank and add fresh fuel. If this does not solve the problem, it may be related to excessive fuel caused by problems in the gas lines and filters.

What causes a chainsaw to vapor lock?

Vapor lock occurs when the fuel (usually gasoline) within the fuel delivery system overheats and vaporizes too rapidly. The resulting excess gas bubbles accumulate to the point of actually blocking normal fuel delivery.

How long does it take to Unflood a chainsaw?

The first option is the easiest since it doesn’t require any effort on your part, it just takes time. Many people wonder if a flooded chainsaw will fix itself? The answer is yes, but not always. By letting the chainsaw sit for about 20 minutes it will allow some of the fuel inside the engine to evaporate.

How do I adjust the compression on my chainsaw?

Too much or too little air intake can negatively affect engine compression. In order to increase compression in your Poulan chain saw’s Kohler engine, manually adjust the air valves via the two rocker arms under the air valve cover.

Will a chainsaw run with low compression?

Most chainsaws will operate well with compression readings that range from 100 to 160 psi. After checking the function of the starter assembly, the operator can move on to determining if compression is dropping or increasing.

How do you start a stubborn chainsaw?

Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.

Why is it hard to start my Stihl chainsaw?

Problems starting a Stihl chain saw can be related to gasoline storage, spark plugs, and incorrect starting procedures.

Should I start chainsaw with brake on or off?

Check the Chain Brake When engaged, the chain brake stops the chain from rotating around the saw’s guide bar. When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.

Why does my chainsaw bog down when I give it gas?

If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.

How do you stop vapor lock?

Once the fuel system has cooled, you can help eliminate any vapor left in the fuel system by first pressing the accelerator pedal slightly (do not press it to the floor) while cranking the engine. Once the engine starts, hold the accelerator pedal down until the vehicle runs smoothly, indicating the vapor lock is gone.

How do I know if my chainsaw spark plug is bad?

If it’s not producing any sparks at all, your chainsaw needs a new plug. If there are only a few sparks coming out of one side of the electrodes but none on the other side, it’s not bad enough for you to worry about, but it will affect your performance.

How long should I let a flooded engine sit?

Perhaps the best remedy for a flooded engine is time. Simply open the hood of your car and let excessive fuel evaporate for as long as you can. After about 20 minutes try starting your car again without hitting the gas pedal. If this still does not work, you may have to check your spark plugs.

What causes chainsaw to flood?

There could be various causes: incorrect fuel mixture, carburation not calibrated properly, or a wet spark plug. In spite of their power and robustness, chainsaws are actually rather delicate machines that require careful and precise maintenance at every stage of their life cycle.

Will a flooded engine fix itself?

Will a flooded engine fix itself? No. You have to take appropriate measures to restore the fuel and air balance in your car’s engine.

Leave a Reply

Your email address will not be published. Required fields are marked *